Panasonic DP-200 manual Paper Entry Area, Open the right cover

Page 51

Problem Solving

■ Paper Entry Area

CMake sure that the misfeed indicator goes off after removing all misfed paper.

1

Open the right cover.

 

2

Remove the misfed paper.

 

3

Continued on the next page...

#Open the heat roller cover.

$If copy paper is fed far into the copier, turn the right paper clearing knob.

%Remove the misfed paper.

I

ATTENTION CMake sure that the misfeed indicator goes off after removing all misfed paper.

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents English DP-2000Common Features and Usage Operation ChartEnergy Star Table of Contents Problem Solving OptionsOthers Precautions For Your SafetyLaser Safety Handling Toner and Paper Ventilation PrecautionsFCC Warning For U.S.A InstallationControl Panel Stop Key Contents Refer to Function KeyReset Key Clear KeysCursor Keys Contents Refer to Book KeyEdge Key Margin KeyFull Size Copying Basic CopySize Copying with Preset RatiosReduction or Enlargement Copying Select the CopyZoom Copying ZoomPress Cursor F or G keys to select Zoom Ratio # Place approximately 50 sheets of paper into the tray Using the Sheet Bypass$Adjust the side guides Copying on Special Paper, etcBook \ Sided/Original H Copy Duplex CopySided/1-Sided Copy Key OperationSided Copy key Procedure\ 2/2 \ 1/2 \ 2 Copy Press 2-SidedPlaten Book \ 2 CopyPlace the Original on the Platen Book \ 2 Copy1 Copy 1 CopyPress 1 keyCopy Place Press OriginalsKey Margin key MarginBook/Edge/Margin Press Book, Edge orBlank Paper OHP InterleavingPress the Copied key or the Blank key OHP InterleavingTo recall a job stored in memory To store a job in memoryInterrupt Mode Energy Saver/Interrupt ModeEnergy Saver Mode Sleep ModeSkyshot Mode Setting the Digital Skyshot ModeProceed as Follows Copying with the Manual Skyshot Mode Setting the Manual Skyshot Mode Press the Function KeySet Manual Skyshot mode first Platen Upper- left corner SIDED/ORIG Combined Function TableSort CopyInput Identification Code Using Function Modes to Change the Initial Copy ModesFunction OptionsGeneral Functions Modes Function Initial SettingCopier Settings General Functions for Key Operator Copier Settings for Key Operator Changing the Auto Exposure Setting Function SettingChanging the Paper Size Function Setting for Key OperatorPaper Guide a Stopper Guide b Departmental Counter Counter 6 digits Components AccessoriesComponents FeaturesAutomatic Document Feeder ADF DA-AS200/i-ADF DA-AR250Inappropriate originals OperationPlace OriginalPress Sort/Finish key Finisher/Exit Guide UnitDA-FS200 Finisher Platen Face-UpPull out the tape Replacing the staple cartridgeReinstall the staple cartridge #Open the staple cover Problem Solving Adding Paper JSheet Paper Tray Straight out Replacing the Toner Cartridge and Waste Toner Box ?Open the front cover Slowly pull the waste toner boxWell Install the new toner cartridge intoInstall a new waste toner box Shake the new toner cartridgeMisfeed Indicator Removing a Misfeed PaperPaper Misfeed Locations Finisher Paper Transport Area Removing a Misfed PaperOpen the right cover Paper Entry AreaClose the right cover Automatic Duplex Unit ADUSystem Console ADF/i-ADF #Lift up the ADF Input Tray Action TroubleshootingBefore Calling Service CheckPlaten Cover As a rule, clean weeklyLight Copies Marked CopiesReplacing the Battery Battery Replacement Required MessageBattery Replacement Procedure DP-2000 Copier SpecificationsADF DA-AS200, i-ADF DA-AR250 Bin Finisher DA-FS2002nd/3rd/4th Paper Feed Module DA-DS210/DA-DS200 Part Name Remarks Options and SuppliesFor Printer For FaxWarranty
Top Page Image Contents