Panasonic CF-30 appendix Error Code/Message

Page 24

Troubleshooting

Error Code/Message

Follow the instructions below when an error message or code appears. If the problem persists or if the error code/mes-

sage is not shown here, contact Panasonic Technical Support (

page 36).

 

 

 

 

 

Error Code/Message

 

Solution

0211 Keyboard error

Disconnect external keyboard or mouse.

0251 System CMOS

An error has occurred in the memory of Setup Utility settings. This occurs when the memory

checksum bad -

content is changed by an unexpected program operation, etc.

Default configuration

Start the Setup Utility and return the settings to the default values, and then change the

used

settings as necessary.

 

 

 

 

If the problem persists, the internal clock battery may need to be replaced. Contact

 

Panasonic Technical Support (

page 36).

0271 Check date and

The date and time settings are not correct.

time settings

Start the Setup Utility and set the correct date and time.

 

If the problem persists, the internal clock battery may need to be replaced. Contact

 

Panasonic Technical Support (

page 36).

0280 Previous boot

Startup has failed repeatedly, so the Setup Utility settings have been returned to the default

incomplete - Default

values to startup the computer.

 

 

 

configuration used

Start the Setup Utility and return the settings to the default values, and then change the

 

settings as necessary.

 

 

 

Press <F2> to Setup

Write down the error details and press

 

to start the Setup Utility. Change the settings

F2

 

if necessary.

 

 

 

0613: Serial Port*1 con-

The I/O and IRQ settings of the serial ports are in conflict.

figuration changed

Run the Setup Utility and in the [Advanced] menu, change the port’s settings so there is

0614: Serial Port*1

no conflict.

 

 

 

config. error - device

 

 

 

 

disabled

 

 

 

 

*1 “A” or “B” appears

 

 

 

 

here to indicate the

 

 

 

 

name of the conflict-

 

 

 

 

ing port.

 

 

 

 

Operating System not

The operating system is not installed in the floppy disk or the hard disk that you are going to

found

boot from.

 

 

 

 

If using a floppy disk, change the disk to the one you can use for boot.

 

If using the hard disk, check if the hard disk is recognized in [Information] menu of the

 

Setup Utility. If the hard disk is recognized, perform the reinstallation ( page 22). If not,

 

contact Panasonic Technical Support ( page 36).

 

If a device is connected to the USB port, disconnect the device, or set [USB Port] or

 

[Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility.

 

If a device is connected to the ExpressCard slot, disconnect the device, or set

 

[ExpressCard slot] to [Disable] in the [Advanced] menu of the Setup Utility.

RAM Module Failed

When the RAM module is not inserted correctly or the RAM module is not conforming to the

 

computer’s specifications, a beep will sound and the “RAM Module Failed” message will be

 

displayed when you turn the power on.

 

Slide the power switch for four seconds or longer to turn off the computer, confirm that

 

the RAM module conforms to the specifications, and reinsert it.

To start the Setup Utility

ARestart the computer.

BPress F2 several times while [Panasonic] boot screen is displayed.

24

Image 24
Contents Contents Personal ComputerIntroduction Terms and illustrations in these instructionsCopyright Disclaimer Trademarks Read Me First Models for U.S.ARead Me First Models for CanadaIndustry Canada IC Notice for modem Models for Europe Canadian ICES-003Industry Canada RF Exposure WarningLithium Battery / Pile au lithium Information to the UserPrecautions Precautions Battery Pack Do Not Turn the Volume Up to Loud When Using Head- phonesDo Not Use with Any Other Computer 35-M-1 Description of Parts SD Memory Card Indicator Blinking During access Ieee 1394 Interface ConnectorExt Antenna Connector Expansion Bus Connector Right sideDescription of Parts Insert the battery pack AC Cord Battery PackFirst-time Operation Operating Instructions This bookConnect your computer to a power outlet Setup WindowsFirst-time Operation Turn on the computerWindows Update Create a new accountRegarding Windows XP To access the Reference Manual To access the Important TipsOn-screen Manual Reference ManualHandling and Maintenance When using peripheral devicesOperation environment Handling cautionsHandling and Maintenance MaintenanceTo clean the LCD panel To clean areas other than the LCD panelHard Disk Backup Function Recover Pro InstallationClick Next PreparationHard Disk Backup Function Recover Pro Complete BackupComplete Restore Hard Disk Data Erase Utility Press 2 to execute 2. Erase HDDPress Space Reinstalling Software Turn the computer off by using the power switch PressPerform the first-time operation Error Code/Message Troubleshooting Basic Starting UpTroubleshooting Basic Entering PasswordShutting down DisplayFn + F2 Touch Pad / Touchscreen only for model with touchscreenRecover Pro OthersHardware Diagnostics Regarding the PC-Diagnostic UtilityHardware Diagnostics Running the Diagnostic CheckConnect the AC adaptor and turn on the wireless switch. Press While Panasonic boot screen is displayedTroubleshooting Limited USE License Agreement About Intel software productsContrat de licence d’usage limité LicenceTermes, clauses et conditions Specifications Main SpecificationsWireless LAN Only for model with wireless LAN BluetoothTM Only for model with BluetoothSpecifications For U.S.A Limits and ExclusionsLimited Warranty For CanadaMemo Panasonic Computer Solutions Company Panasonic Canada Inc