Panasonic CF-30KTPAXxM Disassembly/Reassembly, Removing the Battery Pack, Preparation HDD Pack

Page 24

9 Disassembly/Reassembly

Note:

Power off the computer. Do not shut down to the Suspend or hibernation mode.

Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.

9.1.	Disassembly Instructions	9.1.2. Removing the Battery Pack and
9.1.1.	Preparation	HDD Pack
9.1.1.	Preparation

Before disassembling, be sure to make the following prepara- tions.

•Shut down Windows and turn off the power.

•Disconnect the AC adaptor.

•Remove the optional DIMM memory card and PCMCIA card if they are connected.

•Remove other devices if they are connected.

Attention:

•Please execute writing BIOS ID when you exchange the Main Board.

•Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.

Battery

Cover

HDD Cover

Battery Pack

HDD Pack

1.Open the Battery Cover.

2.Remove the Battery Pack.

3.Open the HDD Cover.

4.Remove the HDD Pack.

9-1

Image 24

Contents Model No. CF-30KTPAXxM How to replace the fuse For U.KLaser Safety Information Safety Precautions Precautions Battery Pack Contents Specifications Main SpecificationsWireless LAN Only for model with wireless LAN Only for North America Tooth Disabling/Enabling Wireless Communi Names and Functions of PartsReady. It does not necessarily indicate the On/Off C D E F G H Diagram BlockDiagnosis Procedure Troubleshooting Power-On Self Test Boot Check Error Diagnosis by Checking Beep Signal SoundBeep signal sound Error message Outline of PostStuck key 02F0 CPU ID When you execute an automatic test Self Diagnosis TestOperation of PC-Diagnostic Utility Selection of tested device DMA, INT, TIMER, RTC operation are confirmed Memory access pattern based onT . technology Record area frequently accessed Wireless LAN modem controllerContent of Standard Test Content of Extend Test Express Card ConnectorWiring between Super I/O Test ItemWiring Connection Diagram Disassembly/Reassembly Removing the Battery PackPreparation HDD Pack Removing the HDD Antenna Cableblack Removing the Dimm Cover and Bot Tom Cover Antenna PCBConnector Connector CN801Removing the FPC HDD BAT Removing the PAD PCBMP PCB SD PCB LID Removing the Handle and Power Removing the Display Unit RDYRemoving the Inverter PCB, TS PCB and LCD Unit Removing the Antenna PCB LSetting the Antenna PCB L and R Arranging the Antenna L and R CablesSetting the Inverter PCB, TS PCB and LCD Unit Preparation of InverterINV PCB Assembly of LCD Unit Preparations LCD CableLCD Cable TOP Case INV-PWBAssembly of LCD Unit Only the model who doesnt have T/S Insert the CNNEW GPS Process the Cable fromScrew ANT Corner ScrewScrew Antenna ElementSetting the Display Unit Screws N9 DRYN4+J10FKL Screws N10 DXSB4+15FNLBConnection of LCD Cables Be overlappedSetting the Handle and Power SW Set the WM SW using the 2 Screws K2-42Set the Power SW Fix the Handle Base L / R using the 2 Screws K2-41Preparation of SW LED FPC Assembly of Power SW Assembly of Palm Top CoverSetting the I/O PCB O㩷SUB PCBPaste Insulation with a chassis Tighten ScrewSetting the SD PCB, Express Card Pcmcia Card S1Insulation S2Bitten S3Sharp Edge S4Part No. Check S5OtherSetting the Main PCB 2NGCUGKPUWNCVGVJG S1 YJGTGQWJCXGPQ ECDNGENQVJGUMDC Assembly of LAN, Modem and MDC Assembly of Main PCB ChassisSetting the PAD PCB PWB PADTape LED PWBSetting the FPC HDD BAT Preparation of HDD FPC ASS’YBatt HDD Guide FPC CushionFPC FIG1 Setting the USB PCB and Antenna PCB FPC Assy #VVCEJANT SW PCB #VVCEJ LCDAssembly of USB / Antenna PCB Setting the Dimm Cover and Bot- tom Cover Preparation of Dimm CoverAttach the Dimm Cover Spacer Dimm Cover is set ~ 0.5mm Setting the W-LAN Module, GPS PCB and Bluetooth PCB Connect the Cable to the Connector CN25Set W-LAN Module LANSetting the KB Cable Cover, Keyboard and LCD Cable Cover Cable SheetWhip ANT Cable SUB ANT Cable Main ANT Cable Assembly of LCD Cable Plate Arranging the KeyboardLCD Cable Cover Cushion Setting the HDD Screws N2 DRHM5054XA Screws N6 DRQT26+E4FKLHDD U Case Ass’y Connect Connector Insert HDD FPC Ass’y Preparation oh HDD ASS’YFit to the corner Hwater Fixed Tape CenterPush and bend Attach it to HDD closely not to loosen HDD Cushion BlackMetal Plate Longer Direction Attach the HDD Cushion YelllowSEC HDD Ass’y insertion Sata Guard is installed Setting the Battery Pack and HDD Pack Set the HDD Pack Set the Battery PackExploded View CF-30KTPAXxMK1-4 19 0.02 N.m 0.2 kgf.cm45 0.05 N.m 0.5 kgf.cm19 + 0.02 N.m 216 + 0.0196 N.m314 + 0.0196 N.m 441 + 0.049 N.mScrew tightening torque 45 + 0.50 N.m 13.0 + 2.0 kgf.cmK9-1-4 Screw tightening torque N13 Replacement Parts List Accessories CN Latch Lever Speaker Case a Hinge Cover L DFHR8521ZA Batt CN PIN Cushion DFHR3N35ZA Busteraid Sheet NRP 851 857 861 872 97, 100, 114 26, 46, 47, 48, 50 F1G1C104A042 CAPACITOR, 16V, 0.1µF358 756761 766 768 769 770 771 773 774 775 776 778 779 853, 854209 K1MN50AA0018K1MN40AA0018 K1KA14AA0266CN 7, 8, 11 K1MY40BA0220 K1KY10BA0214K1MN80BA0246 K1MY30AA0158C3FBNY000187 C2CBYY000639 C0CBCBC00181 C1CB00002983IC 31, 86 C0JBAS000215 IC 32, 61, 68, 87, 108 C0JBAA00036248, 64, 69 J0JYC0000098 G1C1R0MA0380G1C1R0MA0289 G1C100MA007733, 45 951 68, 70481 650 10, 240, 37485, 245, 491, 492 499, 624, 632, 634 881, 882, 889, 895 900 92293, 94, 96 D1HY5608A007 95, 100 D1H85604A024348 349RESISTOR, 1/16W, 9.09KΩ 365 RESISTOR, 1/16W, 680KΩ 368 370, 655656 RESISTOR, 1/16W, 6.98KΩ 658RESISTOR, 1/16W, 1.5KΩ 661 RESISTOR, 1/16W, 3.9W 663, 664RESISTOR, 1/16W, 100Ω 100, 101CAPACITOR, 6.3V, 120µF 100 K1KA14BA0014 101, 102 K1FY104BA024802 RESISTOR, 1/16W, 2.2KΩ 808 D1H81034A024SW 800 800 H2D400400012 OSCILLATOR, 4MHz