System Programming
Other Programs
•Host PBX Access Code Assignment
Assigns a Host PBX access code to make an outside call, if the system is installed behind the host PBX. A pause is automatically inserted after the access code and the toll restriction feature applies to the number after the code. Input Format: #21 [A] [code] #
•[A]=1: CO1/ 2: CO2
•[code] = 2 digits max. (Default : Not stored)
•Hookswitch Flash Time Assignment
Sets the time to send the flash signal to each CO line.
Input Format: #22 [A] [B]
•[A]=1: CO1/ 2: CO2
•[B]=0: 80 ms/ 1: 100 ms (default)/ 2: 160 ms/
3:300 ms/ 4: 600 ms / 5: 900 ms /
6:1200 ms
•Tone Waiting Time After OGM
Sets the time between sending an outgoing message and sending the ringback tone. Input Format: #40 [A]
•[A]=0: 0 SEC/ 1: 5 SEC (default)/ 2: 10 SEC/
3:15 SEC
•Hold Recall Time
Assigns the length of the hold recall timer and transfer recall timer. The hold recall timer is used to alert an extension that a call has been held for an extended period of time. The transfer recall timer is used to alert an extension that a transferred call has not been answered for an extended period of time.
Input Format: #50 [A]
•[A]=0: 30 SEC (default)/ 1: 1 MIN / 2: 2 MIN/
3:3 MIN/ 4: 4 MIN/ 5: DISABLE
•CO Pulse Selection
Assigns to send the pulse to CO line during a conversation with an outside party when the “#01 Dial Type Selection” program is assigned as “Pulse”.
Input Format: #23 [A]
•[A]=0: DISABLE/ 1: ENABLE (default)
•Call Incoming Mode Selection
Assigns whether to use the DISA feature or not. This program is available when the DISA/FAX Detect card is installed.
Input Format: #24 [A] [B]
•[A]=1: CO1/ 2: CO2
•[B]=0: NORMAL (default)/ 1: DISA
•Bell Off Detection
Sets the time between one bell signal detection and the next signal from a Central Office. Input Format: #25 [A]
•[A]=1: 6 SEC/ 2: 3 SEC (default)
•Intercom Alerting Assignment
Assigns the intercom alerting mode to each extension when an intercom call reaches. Input Format: #30 [A] [B]
•[A]=1 through 6 (corresponding to extension no. 21 through 26)
•[B]=0: TONE (default)/ 1: VOICE
•Paralleled Telephone Connection
Assigns whether each extension will be con- nected in parallel with a single line telephone or not.
Input Format: #31 [A] [B]
•[A]=1 through 6 (corresponding to extension no. 21 through 26)
•[B]=0: DISABLE (default)/ 1: ENABLE
•Hold Mode Selection for SLT
Assigns the method to put a call on hold with SLTs.
Input Format: #51 [A]
•[A]=1: MODE 1 (hooking) (default)
2:MODE 2 (hooking and dial 6)
•CO Line Access Number Selection
Selects the automatic line access number. Input Format: #52 [A]
•[A]=1: 9 (default)/ 2: 0
•Conference Tone
Assigns whether or not to delete the conference tone. You hear the tone when the conference or the executive busy override feature begins and finishes.
Input Format: #53 [A]
•[A]=0: DISABLE/ 1: ENABLE (default)
•Music on Hold Use
Selects whether or not to use internal music as the music on hold.
Input Format: #54 [A]
•[A]=1: MODE 1 (NO MUSIC) (default)/
2:MODE 2 (MUSIC)
28