Panasonic PT-DW7000U, PT-D7700U manual Raster position

Page 67

ADVANCED MENU

Press the “ENTER” button.

DIGITAL CINEMA REALITY

AUTO

The ADVANCED MENU screen will be displayed.

FORMAT

SMPTE

Select “SYNC.TERM” with the

BLANKING

INPUT RESOLUTION

buttons.

CLAMP POSITION

EDGE BLENDING

OFF

Switch the input impedance (signal

SYNC.TERM

75

RASTER POSITION

level) of the synchronization signal

with the

buttons.

:MENU SELECT

• These buttons toggle between 75 Ω and HI-Z

(TTL).

:CHANGE

SYNC.TERM

Signal level

Input impedance

75 Ω

Amplitude: 0.6V[p-p] to 4.0V[p-p]

75 Ω

HI-Z (TTL)

High level: 2.0 V or over

1 kΩ

Low level: 0.8 V or lower

Note • Switch the input impedance according to the input signal.

•The factory default is 75 Ω.

•The clock phase and image position may become out of balance during this switching operation. Please make readjustment accordingly.

Raster position

When the whole area where the input picture can be displayed is not used, the picture can be moved to any position inside the display area.

Procedure of adjustment

MAIN MENU

PICTURE

POSITION

ADVANCED MENU

LANGUAGE

OPTION

TEST PATTERN

SIGNAL LIST

SECURITY

ADVANCED MENU

DIGITAL CINEMA REALITY AUTO

FORMATSMPTE

BLANKING

INPUT RESOLUTION

CLAMP POSITION

EDGE BLENDING OFF

SYNC.TERM75

RASTER POSITION

Press the “MENU” button.

The MAIN MENU screen will be displayed.

Select “ADVANCED MENU” with the buttons.

Press “ENTER” button.

The ADVANCED MENU screen will be displayed.

Select “RASTER POSITION” with the buttons.

RASTER POSITION

V:0

H:0

Press the “ENTER” button.

The RASTER POSITION screen will be displayed.

Adjust the position with the , , and buttons.

Press the “MENU” button three times.

The on-screen indications disappear and the normal screen appears again.

(Continued on next page)

67

Image 67

Contents Commercial Use PT-DW7000UModel number PT-D7700U / PT-DW7000U Dear Panasonic CustomerPage Contents Precautions with regard to safety Do not insert any foreign objects into the projector Insulate the battery using tape or similar before disposalUse only the Specified battery Do not place liquid containers on top of the projectorDo not look into the lens while the projector is being used AccessoriesDo not use the old lamp unit Precautions on handling Examples of system expansion When the operation mode selector is set to Projector Remote controlName and function of parts When the operation mode selector is set to Computer Front and side of the projector Rear view of the main unit Controls on rear panel RGB YPBPR1 input terminal pages 26 Side-mounted connection terminalsVideo in terminal Video OUT terminalEffective range of remote control operation Using the remote control unitLoading dry cells Setting projector ID number to remote control Using a wired remote control Using the remote control as a PC mouseOperation mode selector switch Projection scheme InstallationAdjusting the leveling feet Installation geometryProjection distance SH Effective screen height Installation 11810 ET-D75LE3 Aspect ratio Projection distance L formula Units m Before starting connection Connection· SYNC/Y SDA HD/SYNC SCL Video deck TBC built-in Color monitor Control PC Example of connecting with Video devicesVideo deck TBC built-in High-vision video deck Example of connecting with personal computers Signal selector Example of connecting with the signal selectorInstalling the input module Installation of input module optionalTypes of the input modules optional Procedure of installation ET-MD95RGB Connecting signals to the input moduleSUB BNC Connecting the signal to the analog RGB signal input moduleConnecting the component signals RGB signal input module optionalConnecting the video signals Connecting the signal to the video signal input moduleVideo signal input module optional Connecting the component signals Serial digital input module optional ET-MD95SD2 for 480p/480i/576i Auto Pin No Signal Connecting signals to the DVI signal input moduleDVI-D input module optional How to remove the projection lens How to install the projection lensRoughly adjust the focus of the lens. Refer to Powering up the projectorMaking adjustment and selection Press the l button. on the main unit or the remote controlProjection Powering off the projectorAdjustment range after lens position optical shift How to adjust the lensChoose an item and adjust it using Buttons How to adjust the lens for addressing unevenness of focusing Automatic adjustment Auto Setup Press the Menu button Registration of input signal dataRenaming the registered signals Registration of new dataClearing the data of registered signals How to erase sub memory How to register into sub memorySub memory Memory no A1 On-screen indicationsRestrictions Using the Shutter function Using the Freeze functionUsing the digital zoom D.ZOOM + function Structure of menu screens On-screen menusReturning to the previous screen Menu items settingResetting to the factory default Basic operations on menu screenSwitching the picture mode Adjusting the pictureSelect Picture with the buttons Press the Enter button Adjusting Contrast / Bright / Color / Tint Select Picture with Registering the picture mode settings as presettingsSelect OK with Buttons Press the Enter button Select the Dynamic Iris setting with Buttons Dynamic Iris settingOperation Adjustment Remarks Adjusting the color temperatureTo display pictures complying with the sRGB standard Procedure of adjustmentAdjustment items Operation Sharpness / Gamma / Noise reductionShift adjustment Adjusting the positionSize adjustment Size modes Clock phase adjustmentSelect Clock Phase with Adjust the clock phase withSelect Keystone with the buttons Press the Enter button Adjust the Keystone horizontally With the buttonsAdjust the vertical Linearity with Buttons Keystone distortion correctionSelect Advanced Menu with the buttons Press Enter button How to use Advanced MenuSignal level Format To input Betacam with YCbCrSelect Blanking with the buttons Press the Enter button Blanking adjustmentTotal DOTS, Display DOTS, Total Lines and Display Lines Adjusting the input resolutionSelect Advanced Menu with the buttons Press the Enter button Adjusting the clamp positionSpecify the area to be adjusted with the buttons Edge blending adjustmentAdjustment marker Select Advanced Menu with the buttons Edge blending adjustment continuingRaster position Raster position continuing When 54 pictures are displayed when Sxga signals are inputWhen 43 pictures are displayed Changing the display languageHow to change the system format How to use RGB Reality mode ID number need not be set when only one projector is used Option settingsID number setting Procedure of settingFRONT-F FRONT-C REAR-C REAR-F Installation SettingLamp select Lamp powerPress and buttons to select Option Press and buttons to select RS232C SettingPosition of on-screen indications System informationThese values can be adjusted from 0 to 2 Adjustment Adjusting color matchingSelect Option with the buttons Press Enter button Select Target Data with the buttons Press the Enter button Adjusting the color matching using a colorimeterSelect Measured Data with Buttons Press the Enter button Using the buttons, switch to the desired mode Video settingAutomatic adjustment Using the buttons, select Auto Setup Press the Enter buttonAuto signal Output resolution D7700U onlyFan control Use the buttons to select OFF, User 1, User 2, or User Password Setting FUNC1List of P in P How to change the signal for the ET-MD95VM2 optional Examples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingConnecting to a PC Computer Projector DTE specifications Control commandsCable specifications CommandExternal appearance Using the Remote 2 terminalPin assignments and control Sub 9-pin femaleRS-422 control functions Displaying the internal test patternCycle of displayed internal test patterns Setting the password Setting the securitySelect Security with the buttons Press the Enter button Changing the text Changing the passwordSetting the text Set the password with the , , and buttonsSelect CP Option with the buttons How to use CP OptionSetting the on-screen indication function Hold down the Menu button for 3 or so secondsSetting the system format Example of connection How to use network module optionalName and function of network module parts Initial setting of network module Port No Initial setting of network module continuingAccessing from the Web browser Items Function DescriptionTop Network settingNetwork setting Advanced control Monitor information Mail settingSmtp Mail setting page continuing Image file control Monitor Indication of monitor lampLamp Information Checkpoint Remedial measure IndicationDismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterTiming of lamp unit replacement Replacement of lamp unit101 Procedure of lamp unit replacementSystem Information with On the projector or the remote controlPress the Enter button to display Option screen, and selectNo image appears on Symptoms CheckpointPower does not turn on Remote control doesSpecifications Video signal input module Length of power supply cord CabinetOutside dimensions Remote control Power sourceAppendix Compatible RGB/YPBPR SignalsTrademark Acknowledgement Outside dimensionsConcernant LA Sécurité Ne pas retirer le couvercle ou le modifier Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas mettre d’objets étrangers dans le projecteur Ne pas placer le projecteur sur des surfaces instablesNe pas placer des récipients de liquide sur le projecteur Ne démontez pas le bloc lampe’utiliser que la pile indiquée Ne pas placer d’objets lourds sur le projecteurNutilisez pas un bloc lampe usagé Précautions pour la manipulation Nettoyage et maintenanceMise au rebut Période de remplacement de la lampe Remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Procédure de remplacement de la lampe115 Panasonic Canada Inc Technical Support