Panasonic PT-D7700U, PT-DW7000U manual Precautions on handling

Page 8

Precautions on handling

Precautions on transport

The projection lens is susceptible to vibrations and impacts. Be sure to always remove the lens during transport.

Precautions on installation

Be sure to observe the following precautions when installing the product.

Avoid installing the product in a place exposed to vibrations or impacts.

If the projector is installed in a place where vibrations are transmitted from a source of driving power and others or mounted in a car or a vessel, vibrations or impacts may be transmitted to the product to damage the internal parts, causing failure. Install the product in a place free from vibrations and impacts.

Do not install the projector near high- voltage power lines or power sources.

The product may be exposed to interference if it is installed in the vicinity of high-voltage electrical power lines or power sources.

Precautions on use

To view clear images:

The audience cannot enjoy high-contrast and clear images if outside light or the illumination interferes the screen surface.Draw window curtains or blinds, turn off the lightings near the screen or take other proper measures.

In rare cases, wafture can occur on the screen affected by the warm air from the exhaust port depending on the environment.

Do not touch the surface of the projection lens with bare hand.

If fingerprints or stains are left on the projection lens surface, they are magnified and projected on the screen. Keep your hands away from the lens. Cover the lens with the supplied lens cap when the projector is not used.

Screen

If the screen has stains, flaws or discoloration, clear images cannot be viewed. When handling the screen, be careful not to apply volatile substances or leave flaws or stains on the screen.

Do not place the projector on a vinyl sheet or carpet.

If a vinyl sheet sucked up and blocks the air filter intake port, the internal temperature of the projector may increase, which triggers the protection circuit, turning off the power.

Be sure to ask a specialized technician when to install the product to a ceiling.

If the product is to be installed hanging from the ceiling, purchase an optional hanging attachment (for high ceiling: Model No. ET-PKD75) (for low ceiling: Model No. ET-PKD75S) and call a specialized technician for installation.

Do not place the projector over 2 700 m (8881.5') above sea level. When using it over 1 400 m (4605.3') above sea level, set the “Fan Control”, described on page 78, to “HIGHLAND”.

Otherwise the life of the product may be shortened.

Lamp

A mercury lamp with high internal pressure is used for the light source of this product. A high-pressure mercury lamp has the following characteristics:

It may burst with a loud sound or end its life cycle by not illuminating because of given impacts, flaws, or deterioration due to used hours.

The life cycle of a mercury lamp varies according to the individual difference or conditions of use. In particular, turning the power on and off frequently and/or repeatedly will greatly affect the life cycle.

In rare cases, it may burst shortly after the first lighting.

The possibility of burst increases when the lamp is used beyond the replacement time.

Disposal

To discard the product, call the dealer or a specialized dealer.

Cleaning and maintenance

Be sure to remove the power cord plug from the receptacle before cleaning.

Use soft and dry cloth to clean the cabinet

If stains are hard to remove, use a cloth dampened with a kitchen detergent solution (neutral) and squeezed to wipe the cabinet and finish with a dry cloth. If a chemical wipe is used, follow its instructions.

Do not clean the lens surface with fuzzy or dusty cloth.

If dust adheres to the lens, it will be magnified and projected on the screen.

Use a soft and clean cloth to wipe off dust.

8

Image 8
Contents PT-DW7000U Commercial UseDear Panasonic Customer Model number PT-D7700U / PT-DW7000UPage Contents Precautions with regard to safety Insulate the battery using tape or similar before disposal Use only the Specified batteryDo not place liquid containers on top of the projector Do not insert any foreign objects into the projectorDo not use the old lamp unit AccessoriesDo not look into the lens while the projector is being used Precautions on handling Examples of system expansion Name and function of parts Remote controlWhen the operation mode selector is set to Projector When the operation mode selector is set to Computer Front and side of the projector Rear view of the main unit Controls on rear panel Side-mounted connection terminals Video in terminalVideo OUT terminal RGB YPBPR1 input terminal pages 26Loading dry cells Using the remote control unitEffective range of remote control operation Setting projector ID number to remote control Operation mode selector switch Using the remote control as a PC mouseUsing a wired remote control Installation Adjusting the leveling feetInstallation geometry Projection schemeProjection distance SH Effective screen height Installation 11810 ET-D75LE3 Aspect ratio Projection distance L formula Units m · SYNC/Y SDA HD/SYNC SCL ConnectionBefore starting connection Video deck TBC built-in High-vision video deck Example of connecting with Video devicesVideo deck TBC built-in Color monitor Control PC Example of connecting with personal computers Example of connecting with the signal selector Signal selectorTypes of the input modules optional Installation of input module optionalInstalling the input module Procedure of installation Connecting signals to the input module ET-MD95RGBConnecting the signal to the analog RGB signal input module Connecting the component signalsRGB signal input module optional SUB BNCVideo signal input module optional Connecting the signal to the video signal input moduleConnecting the video signals Connecting the component signals Serial digital input module optional ET-MD95SD2 for 480p/480i/576i Auto DVI-D input module optional Connecting signals to the DVI signal input modulePin No Signal How to install the projection lens How to remove the projection lensPowering up the projector Making adjustment and selectionPress the l button. on the main unit or the remote control Roughly adjust the focus of the lens. Refer toPowering off the projector ProjectionChoose an item and adjust it using Buttons How to adjust the lensAdjustment range after lens position optical shift How to adjust the lens for addressing unevenness of focusing Automatic adjustment Auto Setup Registration of input signal data Renaming the registered signalsRegistration of new data Press the Menu buttonClearing the data of registered signals Sub memory How to register into sub memoryHow to erase sub memory Restrictions On-screen indicationsMemory no A1 Using the digital zoom D.ZOOM + function Using the Freeze functionUsing the Shutter function On-screen menus Structure of menu screensMenu items setting Resetting to the factory defaultBasic operations on menu screen Returning to the previous screenSelect Picture with the buttons Press the Enter button Adjusting the pictureSwitching the picture mode Adjusting Contrast / Bright / Color / Tint Select OK with Buttons Press the Enter button Registering the picture mode settings as presettingsSelect Picture with Dynamic Iris setting Select the Dynamic Iris setting with ButtonsAdjusting the color temperature Operation Adjustment RemarksProcedure of adjustment Adjustment items OperationSharpness / Gamma / Noise reduction To display pictures complying with the sRGB standardAdjusting the position Shift adjustmentSize adjustment Clock phase adjustment Select Clock Phase withAdjust the clock phase with Size modesAdjust the Keystone horizontally With the buttons Adjust the vertical Linearity with ButtonsKeystone distortion correction Select Keystone with the buttons Press the Enter buttonHow to use Advanced Menu Signal levelFormat To input Betacam with YCbCr Select Advanced Menu with the buttons Press Enter buttonBlanking adjustment Select Blanking with the buttons Press the Enter buttonAdjusting the input resolution Total DOTS, Display DOTS, Total Lines and Display LinesAdjusting the clamp position Select Advanced Menu with the buttons Press the Enter buttonAdjustment marker Edge blending adjustmentSpecify the area to be adjusted with the buttons Edge blending adjustment continuing Select Advanced Menu with the buttonsRaster position When 54 pictures are displayed when Sxga signals are input When 43 pictures are displayedChanging the display language Raster position continuingHow to change the system format How to use RGB Reality mode Option settings ID number settingProcedure of setting ID number need not be set when only one projector is usedInstallation Setting FRONT-F FRONT-C REAR-C REAR-FLamp power Lamp selectPress and buttons to select RS232C Setting Position of on-screen indicationsSystem information Press and buttons to select OptionSelect Option with the buttons Press Enter button Adjusting color matchingThese values can be adjusted from 0 to 2 Adjustment Select Measured Data with Buttons Press the Enter button Adjusting the color matching using a colorimeterSelect Target Data with the buttons Press the Enter button Video setting Automatic adjustmentUsing the buttons, select Auto Setup Press the Enter button Using the buttons, switch to the desired modeFan control Output resolution D7700U onlyAuto signal Use the buttons to select OFF, User 1, User 2, or User List of P in P Setting FUNC1Password How to change the signal for the ET-MD95VM2 optional Using the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connectionControl commands Cable specificationsCommand Connecting to a PC Computer Projector DTE specificationsUsing the Remote 2 terminal Pin assignments and controlSub 9-pin female External appearanceCycle of displayed internal test patterns Displaying the internal test patternRS-422 control functions Select Security with the buttons Press the Enter button Setting the securitySetting the password Changing the password Setting the textSet the password with the , , and buttons Changing the textHow to use CP Option Setting the on-screen indication functionHold down the Menu button for 3 or so seconds Select CP Option with the buttonsSetting the system format Name and function of network module parts How to use network module optionalExample of connection Initial setting of network module Initial setting of network module continuing Accessing from the Web browserItems Function Description Port NoNetwork setting TopNetwork setting Advanced control Smtp Mail settingMonitor information Mail setting page continuing Image file control Indication of monitor lamp Lamp Information Checkpoint Remedial measureIndication MonitorCleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filterReplacement of lamp unit Timing of lamp unit replacementProcedure of lamp unit replacement 101On the projector or the remote control Press the Enter button to displayOption screen, and select System Information withSymptoms Checkpoint Power does not turn onRemote control does No image appears onSpecifications Length of power supply cord Cabinet Outside dimensionsRemote control Power source Video signal input moduleCompatible RGB/YPBPR Signals AppendixOutside dimensions Trademark AcknowledgementConcernant LA Sécurité Précautions concernant la sécurité Ne pas couvrir le filtre et la sortie d’airNe pas surcharger la prise de courant Ne pas retirer le couvercle ou le modifierNe pas placer le projecteur sur des surfaces instables Ne pas placer des récipients de liquide sur le projecteurNe démontez pas le bloc lampe Ne pas mettre d’objets étrangers dans le projecteurNutilisez pas un bloc lampe usagé Ne pas placer d’objets lourds sur le projecteur’utiliser que la pile indiquée Mise au rebut Nettoyage et maintenancePrécautions pour la manipulation Remplacement de la lampe Période de remplacement de la lampeProcédure de remplacement de la lampe La lampe est chaude si elle vient d’être utilisée115 Technical Support Panasonic Canada Inc