Panasonic PT-LB90NTU Care and Replacement Replacing the Lamp unit, JJLamp unit, ON-SCREEN Display

Page 48

Maintenance

Care and Replacement

Replacing the Lamp unit

JJAir filter

The air filter should be replaced when cleaning is ineffective and when replacing the lamp unit. A replacement air filter is provided with a replacement lamp unit (ET-LAB80). Contact an Authorized Service Center for the optional air filter (TXFMZ01VKG7).

JJLamp unit

The lamp unit, ET-LAB80 is consumable and you must replace it regularly. It is recommended that a qualified technician carry the lamp unit replacement and consult with an Authorized Service Center.

JJNote on lamp unit replacement

zzHandle the lamp unit with special care as it is a glass product. Dropping or giving it a shock may cause it to burst or to be damaged.

zzIf you wish to discard the used lamp, please contact your local authorities or dealer and ask for the correct method of disposal.

zzPrepare a Phillips-head screwdriver.

zzWhen replacing the lamp unit, be sure to hold it by the handle.

zzHold the lamp unit horizontally to prevent broken pieces from scattering. When the projector is mounted in the ceiling, do not work directly under the

projector or put your face close to the projector, and pull out the lamp horizontally.

Note

zzPrior to replacing the lamp unit, allow it to cool down to prevent the risk of burns, damage and other hazards.

Remarks

zzDo not attempt replacement with an unauthorized lamp unit.

JJLamp unit replacement time

When the lamp is consumed, the brightness may decrease over time. 3 000 hours of use is the replacing time as a rough guide, and that might be shortened by the usage conditions, characteristics of the lamp unit or environmental conditions. You can find the duration of usage time by checking LAMP RUNTIME in the PROJECTOR SETUP menu. Do not use a lamp unit over 3 000 hours. Failure to observe this may result in explosion of the lamp.

 

ON-SCREEN DISPLAY

LAMP indicator

 

REPLACE LAMP

 

 

 

 

2 800 hours

Displays “REPLACE LAMP” on the upper left of the screen

 

for 30 seconds. If any button is pressed within 30 seconds,

 

 

the message disappears.

Illuminates red, even in the

3 000 hours

Displays “REPLACE LAMP” on the upper left of the screen,

standby mode.

and it will stay until you respond. The power is turned off

 

 

automatically in 10 minutes.

 

 

 

 

Remarks

zzThe guide time, 3 000 hours, is a rough estimate based on certain conditions and is not a guaranteed time.

48 - ENGLISH

Image 48
Contents PT-LB90U PT-LB78VU PT-LB75VU ImportantSafetySafetyNotice Notice Serial numberImportant Safety Notice Declaration of ConformityPanasonic Environment care information for users in ChinaContents Contents SettingsMaintenance AppendixPrecautionswith regardwithtoregardsafety to safety Precautions with regard to safety Do not put your weight on this projector ZzDo not set up the projector outdoorsDo not place the projector in extremely hot locations Always disconnect all cables before mov- ing the projectorCleaning and maintenance SecurityDisposal Precautions with regard to safety Accessories TXFQB02VKJ2Jjinitial Setting Read this firstRead this first JjlanguageAboutYourYourProjectorProjector Projector bodyJJTop and front view JJControl panelAbout Your Projector Back and bottom viewJJTerminals About Your Projector Remote control JJTop viewFront view Setting up Setting upScreen size and throw distance Setting up Projection method Front leg adjusters and throwing angleSetting on a desk/floor Projecting from rear Using translucent screenBefore connecting to the projector Connecting example AV equipmentConnectionsConnections Connections Connecting example Computers Power cord ConnectingJJDisconnecting JJDirect power off functionPower Lock indicator status Power indicator statusIndicator status Status Switching the projector on/off Switching on the projector Connect the power cord. ÆpagePress the Release button to unlock the Power button Press the Power buttonSwitching the projector on/off Switching off the projector Press the Power button againAudio Setting Selecting the input signal Projecting an imageProjecting an image Positioning the imageSwitching the input signal Remotecontrolcontrolope ationoperationCapturing an image Stopping the projection temporarilySetting up the image position automatically Resetting to the factory default settingsControlling the volume of the speaker JJINDEX-WINDOW displayJJButton functions in digital zoom mode Press the Enter button Select OKJJOperating procedure JJResetting to the factory default settingsMenu Navigation Navigating through the MenuON-SCREEN Menu Sub-menuMain menu JjpictureJjprojector Setup PositionJjdisplay Option SecurityPicture Mode Color TemperatureContrast BrightnessStill Mode Daylight ViewNoise Reduction TV-SYSTEMClock Phase Realtime KeystoneKeystone ShiftOver Scan AspectPosition menu Frame Lock JJS43Jjthrough Language menu Language menuClosed Caption Setting DISPLAYOPTIOPTIONmenu menuON-SCREEN Display Auto Setup Signal SearchStartup Logo Display Option menuWide Mode Sxga ModeOther Functions Projector Setup menuPROJECTOR Setup menu Projector Setup menu Standby ModeLamp Power Lamp RuntimeAudio Setting Function ButtonTest Pattern Initialize ALLChange Pattern Password Password ChangeSecurity menu Text DisplayMenu Lock Password Control Device SetupRemote Controller Menu LockJjwired LAN Jjwireless LANJjinput Password Jjstatus Jjpassword ChangeLamp indicator Jjtemp indicatorCare and Replacement Care and ReplacementBefore Care and Replacement Cleaning the projectorCare and Replacement Replacing the Lamp unit JJNote on lamp unit replacementJJLamp unit replacement time JJLamp unitJJLamp replacement procedure Lamp runtime is reset to TroubleshootingTroubleshooting TechnicalInformatiInformation List of compatible signals This projector can project the following image signalsJJPin assignments and signal names JJCommunication settingsTechnical Information Serial terminal JJConnectionCable specifications Control commandsTechnical Information LAN terminalSpecifications ComputerComputer Audio Specifications PT-LB90NTUCeiling mount bracket safeguards Dimensions Trademark acknowledgementsUnit mm Index IndexAvisimportantconcernantconcernantla sécurité la sécurité Numéro de sérieAvis important concernant la sécurité AvertissementDéclaration de conformité Précautions de sécurité AvertissementPendant un orage, ne pas toucher le projecteur ou le câble Ne pas surcharger la prise de courantPrécautions de sécurité Mise EN GardePrécautions lors de l’installation Précautions lors du transportNe pas utiliser une lampe usagée ZzNe pas utiliser le projecteur en extérieurPrécautions lors de l’utilisation SécuritéNettoyage et entretien Mise au rebutRemplacementde lunitédelunitéa lampe de la lampe JJRemarque sur le remplacement de l’unité de la lampeJJFiltre à air JJL’unité de lampeRemplacement de lunité de la lampe JJProcédure de remplacement de la lampeAppuyer sur la touche Alimentation La durée de la lampe est redéfinie sur « 0 »