Panasonic PT-P1SDE manual Setting-up, Projection methods, Projector position, Projection distances

Setting-up

Projection methods

In way of installing projector, any one of the following four projection methods are used. Select whichever projection method matches the setting-up method. (The projection method can be set from the “OTHER SETUP” menu. Refer to page 50 for details.)

BFront-desk projection BFront-ceiling projection

Projector position

Top edge of screen

SH	Screen
	L
	H1

Bottom edge of screen

54 mm (2-1/8˝)

L:Projection distance SH: Image height SW:Image width

H1: Distance from centre of lens to bottom edge of projected image

Getting started

Menu items	Setting
FRONT/REAR	FRONT
DESK/CEILING	DESK

BRear-desk projection (Using a translucent screen)

Menu items	Setting
FRONT/REAR	FRONT
DESK/CEILING	CEILING

BRear-ceiling projection (Using a translucent screen)

SW	L
	Screen

Projection distances

Menu items	Setting
FRONT/REAR	REAR
DESK/CEILING	DESK

NOTE:

Menu items	Setting
FRONT/REAR	REAR
DESK/CEILING	CEILING

4:3 Screen size	Projection distance (L)		Height position
(diagonal)	Wide (LW)	Telephoto (LT)	(H1)
1.02 m(40˝)	—	1.2 m(3´11˝)	0.13 m(5-3/32˝)
1.14 m(45˝)	1.3 m(4´3˝)	1.4 m(4´7˝)	0.15 m(5-7/8˝)
1.27 m(50˝)	1.4 m(4´7˝)	1.6 m(5´2˝)	0.17 m(6-11/16˝)
1.52 m(60˝)	1.7 m(5´6˝)	1.9 m(6´2˝)	0.20 m(7-27/32˝)
1.78 m(70˝)	2.0 m(6´6˝)	2.2 m(7´2˝)	0.23 m(9-1/32˝)
2.03 m(80˝)	2.3 m(7´6˝)	2.6 m(8´6˝)	0.26 m(10-7/32˝)
2.29 m(90˝)	2.5 m(8´2˝)	2.9 m(9´6˝)	0.30 m(11-25/32˝)
2.54 m(100˝)	2.8 m(9´2˝)	3.2 m(10´5˝)	0.33 m(12-31/32˝)
3.05 m(120˝)	3.4 m(11´1˝)	3.9 m(12´9˝)	0.40 m(15-23/32˝)
3.81 m(150˝)	4.2 m(13´9˝)	4.9 m(16´)	0.50 m(19-21/32˝)
5.08 m(200˝)	5.6 m(18´4˝)	6.6 m(21´7˝)	0.66 m(25-31/32˝)
6.35 m(250˝)	7.0 m(22´11˝)	8.2 m(26´10˝)	0.83 m(32-21/32˝)
7.62 m(300˝)	8.4 m(27´6˝)	9.9 m(32´5˝)	0.99 m(38-31/32˝)

BYou will need to purchase the separate ceiling bracket (ET-PKP1) when using the ceiling installation method.

BDo not set up the projector vertically or tilted horizontally, otherwise it may cause damage to the projector.

BIt is recommended that you set up the projector in a place that is tilted at less than ±30° vertically. Setting up the projector in places that are tilted at more than ±30° vertically may shorten component life.

NOTE:

BThe dimensions in the table above are approximate.

BFor details about projected image distances, refer to page 68.

20-ENGLISH ENGLISH-21