Panasonic PT-L795U manual Basic operation, Changing the input signal, Press the Video button

Page 21

Basic operation

Changing the input signal

The input source for picture signals and the corresponding audio signals can be changed by pressing the VIDEO or RGB buttons on the projector operating panel or on the remote control unit. In addition, the name of the input source selected will be displayed on the screen for approximately 5 seconds.

Press the VIDEO button

(Projector)

(Remote control unit)

or

The signal from the source which is connected to the S-VIDEO IN connector or VIDEO IN connector is projected.

If cables are connected to both connectors, the S-VIDEO signal will be selected automatically. (The S-VIDEO signal has priority.)

Press the RGB button

(The source switches between RGB 1 and RGB 2 each time the button is pressed.)

(Projector)		(Remote control unit)
		The signal from the source which is
		connected to the RGB 1 IN connector is
	or	projected.
	or

The signal from the source which is connected to the RGB 2 IN connector is projected.

NOTE:

The mode or format (TV-SYSTEM) of the currently-selected signal will be displayed on-screen underneath the name of the selected signal source. Refer to page 34 for details on how to clear the on-screen display of the signal source name and for the operable button guides which appear in menu screens and in setting and adjustment screens.

If you would like to project the VIDEO signals being input to the VIDEO IN connector, do not connect any cables to the S-VIDEO IN connector.

There is only one audio system circuit provided for the AUDIO IN L-R terminals for S-VIDEO and VIDEO signals. Because of this, if using both S-VIDEO signals and VIDEO signals, it will be necessary to change over the connectors.

When RGB signals are being input, the projection mode will be matched automatically to one of the modes which have been pre-set inside the projector.

The projector is shipped from the factory with the system format selection function set to “AUTO”, so that the system format is selected automatically when VIDEO/S-VIDEO signals are being input.

Refer to page 21 for a list of the different types of RGB signal which can be input, and to page 22 for details on the format selection when VIDEO/S-VIDEO signals are being input.

When RGB 1 or RGB 2 has been selected, the signal selected will be output from the RGB OUT connector.

20

Image 21

Contents LCD Projector Contents FeaturesDear Panasonic Customer Important Safety Notice Setting-up Precautions with regard to safetyWhen using the projector If problems occur during useCleaning and maintenance When using the projectorTake particular care when replacing the lamp unit Do not look into the lens while the projector is being usedPrecautions on handling Wipe the cabinet with a soft, dry clothAbout condensation Remote control unit Location and function of each partFront view Top and front ProjectorSide terminal board Back, bottom and right viewBefore using the remote control unit Inserting the batteriesDo not do any of the following If facing the remote control unit toward the screen Operating range of the remote control unitIlluminating the remote control unit buttons Screen ProjectorVideo Impose Menu operation guidePoint Zoom Refer to Count Down Refer toAudio PositionLanguage Refer to OptionsTurning on the power Turning the power on and offTurning off the power Power button Main Power switchScreen requirements Screen characteristics referenceStandard setting-up positions Standard setting-up dimensionsProjection distance L Maximum Minimum Adjusting the position of the projected picture Retracting the adjustable legs Setting the projector up horizontallyAdjustment procedure Adjuster button Adjustable legsAdjustment procedure for direct adjustment Adjusting the lensSetting procedure Setting-up positions and changing the projection methodFront mounting Rear mountingProjector Remote control unit Changing the input signalBasic operation Press the Video buttonDisplay mode name VGA400 VGA460 RGB signals that can be inputSignal data Svga XGA Mxga Sxga MAC16 MAC21 HdtvAuto Ntcs Operating procedureNTSC4.43 PAL PAL-M PAL-N SecamFreezing the picture Adjusting the volumeSelecting the picture mode Adjusting the picture to the desired setting BAL R BAL G BAL B Adjustment RangeAdjustment procedure for volume adjustment Adjusting the sound to the desired settingCorrecting the picture position automatically Correction procedureWhen adjusting the horizontal position H-POSI Adjusting the picture positionWhen adjusting the vertical position V-POSI Adjustment procedure for horizontal position adjustmentAdjusting the video size For overscanningFor underscanning About dot clock adjustment Using the video impose function Using other useful functionsEnlarging part of the input picture Disabling the Power button of the remote control unit Changing the on-screen display language Setting procedure To change the language to GermanUsing the lens retracting function Using the power save functionSetting procedure Example of connection to audio-visual equipment System configuration exampleAudio system Laser disc player VCRExample of connection to a computer SUB HDSUB About the Macintosh adapter Wireless mouseExample of connection OperationPin layout and signal names for Serial connector Using the serial connectorCommunication Settings Basic formatCable specifications Control commandsLamp indicator Temp indicator Indicator name IndicatorsIndicator display Problem Possible causeCleaning the air filter Clean the air filter and the air filter clamps Replacing the lamp unit Lamp unit replacement periodLamp unit cover Fixing screw for the lamp unit cover Replacement procedurePage Before asking for service, check the following points RGB HD/SYNC RGB OUT Audio Video Audio in L-R SpecificationsFCC Trademark AcknowledgementsDimensions