Fujitsu LT800P warranty Resuming System Operation

Page 32

S t y l i s t i c L T 8 0 0 P T a b l e t

•Suspending system operation interrupts data communications; therefore, some programs may block the system from suspending to prevent an interruption.

•The suspend action of the Suspend/Resume button may be disabled to prevent accidental interruption. If this is the case, pressing the Suspend/Resume button will not suspend system operation as described here. (In this case, suspend mode can only be achieved using the system software). Contact your local help desk or reseller if your system configuration is not suitable.

•If your system is equipped with a PC Card that allows you to connect to a wired or wireless network, you may be logged off the network after a period of inactivity while system operation is suspended. Contact your network administrator or local help desk for details on log-off parameters for your network.

Resuming System Operation

To resume system operation, (from either Suspend-to-RAM or Save-to-Disk modes), press the Suspend/Resume button.

•From Suspend-to-RAM mode

Status lights indicate that the system state is changing. It may take up to a minute before the system returns to the On state and system operation resumes. Note that the display turns on shortly before the pen becomes active due to the power-up sequences observed by the system.

•From Save-to-Disk mode

Active data is read from the hard disk drive, and the system returns to the On state after a short period of time.

Note that power to several system components must be restored before system operation resumes. Allow sufficient time for system operation to resume before attempting to use the system. If your system uses Save-to-Disk mode, it will take longer to resume operation as compared to using Suspend-to-RAM mode. Time is needed to read data from the hard disk drive.

•Use the system as you normally would once system operation resumes.

All programs resume at the point where execution stopped when system operation was suspended.

30

Image 32

Contents

According to FCC Part Y l i s t i c L T 8 0 0 P T a b l e t Table of Contents Care and Maintenance Preface Y l i s t i c L T 8 0 0 P T a b l e t About This Guide Conventions Used in the GuideLimited Warranty Information Service and SupportFujitsu Contact Information Fujitsu OnlineGetting Started Y l i s t i c L T 8 0 0 P T a b l e t Getting to Know Your Tablet In-box ItemsOptional Accessories Peripheral/Accessory Fujitsu Part NumberStylistic LT800P Tablet Features Stylistic LT800P Tablet Features Front ViewFront / Top / Left Features Stylistic LT800P Tablet Features Rear View Rear / Bottom / Right Features Status Display Status Display IconsSystem Status Indicators Mode/State LED State RemarksBattery RAMHovering Connectors and Peripheral Interfaces Left-Side Connectors and InterfacesPeripheral Connectors/Interfaces ConnectorPurpose PeripheralCommunication is about 3 feet, and within Additional System Icons Using the Stylistic LT800P Tablet Y l i s t i c L T 8 0 0 P T a b l e t Using Your Stylistic LT800P System States Power Icon Current State To Change State Appearance Changing System StatesSuspending System Operation Powering Up the TabletShutting Down the System Power icon is blinking Suspend-to-RAMmode Down the system rather than using Suspend-to-RAM mode Resuming System Operation Using Hotpads Stylistic Hotpad ArraysHotpad Keys IconIcon Name Description Using the Pen Calibrating the penTo Calibrate the Pen Replacing the Pen Using Hovering ModeCharging the Battery Pack Removing and Installing the Battery Pack Battery Pack Charging Time90% 100%Removing the Battery Pack Tips for Conserving Battery Power Operation of the Bridge BatteryChanging the Bios Settings Modem ConnectionPC Card Slot LAN Port RJ-45Starting Bios Setup Y l i s t i c L T 8 0 0 P T a b l e t Care and Maintenance Y l i s t i c L T 8 0 0 P T a b l e t Caring for Your Stylistic LT800P Protecting the Display ScreenStoring the Stylistic LT800P Tablet Avoiding OverheatingTroubleshooting Y l i s t i c L T 8 0 0 P T a b l e t Infrared Data Transfer Is Not Working System Will Not Resume OperationDisplay Screen Is Blank or Difficult to Read Audio Volume Too Low Configuring Peripherals InterfacesCursor Is Not Tracking Pen Tablet Is Not Responding to the PenHardware Specifications Y l i s t i c L T 8 0 0 P T a b l e t Stylistic LT800P Hardware Specifications Stylistic LT800P Tablet SpecificationsInterface Specifications Stylistic LT800P Tablet Specifications Power Specifications Environmental SpecificationsAgency Approval Specifications Additional SpecificationsY l i s t i c L T 8 0 0 P T a b l e t Agency Notices Y l i s t i c L T 8 0 0 P T a b l e t Agency Notices Y l i s t i c L T 8 0 0 P T a b l e t DOC Industry Canada Notices Y l i s t i c L T 8 0 0 P T a b l e t UL Notice Y l i s t i c L T 8 0 0 P T a b l e t Appendix Y l i s t i c L T 8 0 0 P T a b l e t Wireless LAN, Health and Authorization for use FCC Regulatory InformationRegulatory Notes and Statements Regulatory Information/DisclaimersExport restrictions FCC Interference StatementFCC Radio Frequency Exposure statement Before Using This Device Characteristics of the DeviceWireless LAN Modes Using this Device AdHoc ModeHow to Handle This Device Infrastructure ModeWorkflow Connecting Windows 2000 SystemsSetting Parameters Table A-1 Profile Parameters DescriptionTable A-2 Encryption Key Setup WEPNetwork Connection Windows Network SettingsTCP/IP Settings Table A-3 Setting an IP Address Checking the full computer name and workgroupTable A-4 Checking computer name and workgroup Setting File and Printer Sharing for Microsoft NetworksSharing Sharing Files Table A-6 Printer Sharing Table A-5 Sharing filesPrinter Sharing Accessing Another Computer Checking the ConnectionChecking the Connectivity Table A-7 Checking connectivityConnecting Windows XP Systems Table A-8 Setting parameters Network Connection Network SettingsTable A-9 Setting an IP address Table A-10 Setting computer name and workgroup SharingSetting File and Printer Sharing for Microsoft Networks Checking the Connection Table A-11 Checking connectivity Problem Possible Cause Possible Solution TroubleshootingTroubleshooting Table Signal Retry the connection Where directory and filename repre If the connection is successful Problem Possible Solution WindowsWindows XP Setting IP Addresses About IP AddressesSpecifications Technical Specifications for Integrated Wireless LAN DeviceY l i s t i c L T 8 0 0 P T a b l e t Index Y l i s t i c L T 8 0 0 P T a b l e t Items included with, 9 Stylistic LT P-867 Specifications Y l i s t i c L T 8 0 0 P T a b l e t 100