Fujitsu LT800P warranty Signal Retry the connection

Page 91

U s i n g t h e W i r e l e s s L A N

Problem

Possible Cause

Possible Solution

 

 

 

 

 

 

Other computers

The TCP/IP

If the TCP/IP protocol is installed, do the

are not displayed

protocol is not

following to check the IP address:

when the [Network

installed, or, the IP

1. Windows 2000:

Computer] icon is

address is not set

Click [Start] -> [Programs] -> [Acces-

double-clicked.

correctly.

sories] -> [Command Prompt].

 

 

(continued)

 

Windows XP:

 

 

Click [Start] -> [All Programs] ->

 

 

[Accessories] -> [Command Prompt].

 

 

2. Enter “IPCONFIG” command, and

 

 

press [Enter].

 

 

(If your hard disk is C drive, enter

 

 

C:\>ipconfig)

 

 

Check that the IP address is correctly

 

 

displayed under the IP Address.

 

 

Example:

 

 

IP address: 10.0.1.3

 

 

Subnet Mask: 255.255.255.0

 

 

Default Gateway: 10.0.1.1

 

 

 

 

No communication

Shorten the distance between computers

 

due to poor radio

or remove visible obstacles between them,

 

signal.

and retry the connection.

 

 

 

89

Page 90 Page 92
Image 91
Page 90 Page 92
Contents
According to FCC Part Y l i s t i c L T 8 0 0 P T a b l e t Table of Contents Care and Maintenance Preface Y l i s t i c L T 8 0 0 P T a b l e t Conventions Used in the Guide About This GuideFujitsu Online Limited Warranty InformationService and Support Fujitsu Contact InformationGetting Started Y l i s t i c L T 8 0 0 P T a b l e t In-box Items Getting to Know Your TabletPeripheral/Accessory Fujitsu Part Number Optional AccessoriesStylistic LT800P Tablet Features Front View Stylistic LT800P Tablet FeaturesFront / Top / Left Features Stylistic LT800P Tablet Features Rear View Rear / Bottom / Right Features Status Display Icons Status DisplayMode/State LED State Remarks System Status IndicatorsRAM BatteryHovering Left-Side Connectors and Interfaces Connectors and Peripheral InterfacesPeripheral Peripheral Connectors/InterfacesConnector PurposeCommunication is about 3 feet, and within Additional System Icons Using the Stylistic LT800P Tablet Y l i s t i c L T 8 0 0 P T a b l e t System States Using Your Stylistic LT800PChanging System States Power Icon Current State To Change State AppearanceShutting Down the System Powering Up the TabletSuspending System Operation Power icon is blinking Suspend-to-RAMmode Down the system rather than using Suspend-to-RAM mode Resuming System Operation Stylistic Hotpad Arrays Using HotpadsIcon Hotpad KeysIcon Name Description Calibrating the pen Using the PenTo Calibrate the Pen Charging the Battery Pack Using Hovering ModeReplacing the Pen 100% Removing and Installing the Battery PackBattery Pack Charging Time 90%Removing the Battery Pack Operation of the Bridge Battery Tips for Conserving Battery PowerLAN Port RJ-45 Changing the Bios SettingsModem Connection PC Card SlotStarting Bios Setup Y l i s t i c L T 8 0 0 P T a b l e t Care and Maintenance Y l i s t i c L T 8 0 0 P T a b l e t Protecting the Display Screen Caring for Your Stylistic LT800PAvoiding Overheating Storing the Stylistic LT800P TabletTroubleshooting Y l i s t i c L T 8 0 0 P T a b l e t Display Screen Is Blank or Difficult to Read System Will Not Resume OperationInfrared Data Transfer Is Not Working Tablet Is Not Responding to the Pen Audio Volume Too LowConfiguring Peripherals Interfaces Cursor Is Not Tracking PenHardware Specifications Y l i s t i c L T 8 0 0 P T a b l e t Stylistic LT800P Tablet Specifications Stylistic LT800P Hardware SpecificationsInterface Specifications Additional Specifications Stylistic LT800P Tablet Specifications Power SpecificationsEnvironmental Specifications Agency Approval SpecificationsY l i s t i c L T 8 0 0 P T a b l e t Agency Notices Y l i s t i c L T 8 0 0 P T a b l e t Agency Notices Y l i s t i c L T 8 0 0 P T a b l e t DOC Industry Canada Notices Y l i s t i c L T 8 0 0 P T a b l e t UL Notice Y l i s t i c L T 8 0 0 P T a b l e t Appendix Y l i s t i c L T 8 0 0 P T a b l e t Regulatory Information/Disclaimers Wireless LAN, Health and Authorization for useFCC Regulatory Information Regulatory Notes and StatementsFCC Radio Frequency Exposure statement FCC Interference StatementExport restrictions AdHoc Mode Before Using This DeviceCharacteristics of the Device Wireless LAN Modes Using this DeviceInfrastructure Mode How to Handle This DeviceSetting Parameters Connecting Windows 2000 SystemsWorkflow Description Table A-1 Profile ParametersWEP Table A-2 Encryption Key SetupTCP/IP Settings Network SettingsNetwork Connection Windows Checking the full computer name and workgroup Table A-3 Setting an IP AddressSharing Setting File and Printer Sharing for Microsoft NetworksTable A-4 Checking computer name and workgroup Sharing Files Printer Sharing Table A-5 Sharing filesTable A-6 Printer Sharing Checking the Connection Accessing Another ComputerTable A-7 Checking connectivity Checking the ConnectivityConnecting Windows XP Systems Table A-8 Setting parameters Table A-9 Setting an IP address Network SettingsNetwork Connection Sharing Table A-10 Setting computer name and workgroup Setting File and Printer Sharing for Microsoft Networks Checking the Connection Table A-11 Checking connectivity Troubleshooting Table TroubleshootingProblem Possible Cause Possible Solution Signal Retry the connection Where directory and filename repre If the connection is successful Windows Problem Possible SolutionWindows XP About IP Addresses Setting IP AddressesTechnical Specifications for Integrated Wireless LAN Device SpecificationsY l i s t i c L T 8 0 0 P T a b l e t Index Y l i s t i c L T 8 0 0 P T a b l e t Items included with, 9 Stylistic LT P-867 Specifications Y l i s t i c L T 8 0 0 P T a b l e t 100
Top Page Image Contents