Fujitsu LT800P warranty Agency Notices

Page 61

A g e n c y N o t i c e s

Agency Notices

NOTICE

Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment.

FCC NOTICES

Notice to Users of Radios and Television

These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar- antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■Reorient or relocate the receiving antenna.

■Increase the separation between the equipment and receiver.

■Connect the equipment into an outlet that is on a different circuit than the receiver.

■Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables must be employed with this equipment to ensure compli- ance with the pertinent RF emission limits governing this device.

Notice to Users of the US Telephone Network

This equipment complies with Part 68 of the FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other infor- mation, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this information or number must be provided to the telephone company.

This equipment is designed to be connected to the telephone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the appli- cable FCC Part 68 rules and requirements adopted by the ACTA. A compliant tele- phone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.

The ringer equivalent number (REN) of this equipment is 0.0B. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming

59

Page 60 Page 62
Image 61
Page 60 Page 62
Contents
According to FCC Part Y l i s t i c L T 8 0 0 P T a b l e t Table of Contents Care and Maintenance Preface Y l i s t i c L T 8 0 0 P T a b l e t Conventions Used in the Guide About This GuideService and Support Limited Warranty InformationFujitsu Contact Information Fujitsu OnlineGetting Started Y l i s t i c L T 8 0 0 P T a b l e t In-box Items Getting to Know Your TabletPeripheral/Accessory Fujitsu Part Number Optional AccessoriesStylistic LT800P Tablet Features Front View Stylistic LT800P Tablet FeaturesFront / Top / Left Features Stylistic LT800P Tablet Features Rear View Rear / Bottom / Right Features Status Display Icons Status DisplayMode/State LED State Remarks System Status IndicatorsRAM BatteryHovering Left-Side Connectors and Interfaces Connectors and Peripheral InterfacesConnector Peripheral Connectors/InterfacesPurpose PeripheralCommunication is about 3 feet, and within Additional System Icons Using the Stylistic LT800P Tablet Y l i s t i c L T 8 0 0 P T a b l e t System States Using Your Stylistic LT800PChanging System States Power Icon Current State To Change State AppearanceShutting Down the System Powering Up the TabletSuspending System Operation Power icon is blinking Suspend-to-RAMmode Down the system rather than using Suspend-to-RAM mode Resuming System Operation Stylistic Hotpad Arrays Using HotpadsIcon Hotpad KeysIcon Name Description Calibrating the pen Using the PenTo Calibrate the Pen Charging the Battery Pack Using Hovering ModeReplacing the Pen Battery Pack Charging Time Removing and Installing the Battery Pack90% 100%Removing the Battery Pack Operation of the Bridge Battery Tips for Conserving Battery PowerModem Connection Changing the Bios SettingsPC Card Slot LAN Port RJ-45Starting Bios Setup Y l i s t i c L T 8 0 0 P T a b l e t Care and Maintenance Y l i s t i c L T 8 0 0 P T a b l e t Protecting the Display Screen Caring for Your Stylistic LT800PAvoiding Overheating Storing the Stylistic LT800P TabletTroubleshooting Y l i s t i c L T 8 0 0 P T a b l e t Display Screen Is Blank or Difficult to Read System Will Not Resume OperationInfrared Data Transfer Is Not Working Configuring Peripherals Interfaces Audio Volume Too LowCursor Is Not Tracking Pen Tablet Is Not Responding to the PenHardware Specifications Y l i s t i c L T 8 0 0 P T a b l e t Stylistic LT800P Tablet Specifications Stylistic LT800P Hardware SpecificationsInterface Specifications Environmental Specifications Stylistic LT800P Tablet Specifications Power Specifications Agency Approval Specifications Additional SpecificationsY l i s t i c L T 8 0 0 P T a b l e t Agency Notices Y l i s t i c L T 8 0 0 P T a b l e t Agency Notices Y l i s t i c L T 8 0 0 P T a b l e t DOC Industry Canada Notices Y l i s t i c L T 8 0 0 P T a b l e t UL Notice Y l i s t i c L T 8 0 0 P T a b l e t Appendix Y l i s t i c L T 8 0 0 P T a b l e t FCC Regulatory Information Wireless LAN, Health and Authorization for useRegulatory Notes and Statements Regulatory Information/DisclaimersFCC Radio Frequency Exposure statement FCC Interference StatementExport restrictions Characteristics of the Device Before Using This DeviceWireless LAN Modes Using this Device AdHoc ModeInfrastructure Mode How to Handle This DeviceSetting Parameters Connecting Windows 2000 SystemsWorkflow Description Table A-1 Profile ParametersWEP Table A-2 Encryption Key SetupTCP/IP Settings Network SettingsNetwork Connection Windows Checking the full computer name and workgroup Table A-3 Setting an IP AddressSharing Setting File and Printer Sharing for Microsoft NetworksTable A-4 Checking computer name and workgroup Sharing Files Printer Sharing Table A-5 Sharing filesTable A-6 Printer Sharing Checking the Connection Accessing Another ComputerTable A-7 Checking connectivity Checking the ConnectivityConnecting Windows XP Systems Table A-8 Setting parameters Table A-9 Setting an IP address Network SettingsNetwork Connection Sharing Table A-10 Setting computer name and workgroupSetting File and Printer Sharing for Microsoft Networks Checking the Connection Table A-11 Checking connectivity Troubleshooting Table TroubleshootingProblem Possible Cause Possible Solution Signal Retry the connection Where directory and filename repre If the connection is successful Windows Problem Possible SolutionWindows XP About IP Addresses Setting IP AddressesTechnical Specifications for Integrated Wireless LAN Device SpecificationsY l i s t i c L T 8 0 0 P T a b l e t Index Y l i s t i c L T 8 0 0 P T a b l e t Items included with, 9 Stylistic LT P-867 Specifications Y l i s t i c L T 8 0 0 P T a b l e t 100
Top Page Image Contents