Fujitsu LT800P warranty Removing the Battery Pack

Page 40

S t y l i s t i c L T 8 0 0 P T a b l e t

2.Slide the spring-loaded battery release switch in the direction indicated in .

3.While holding the switch, slide the battery pack away from the top of the system, as indicated in .

If you are using an external battery charger, refer to the instructions provided with the battery charger.

To install the battery pack:

Orient the battery so the grooves on the sides of the battery align with the slides inside of the battery tray. Slide the battery pack into the tray and press it firmly into the tray until it is seated. When it is properly seated, the battery release switch will automatically latch the battery pack into place.

Once the battery pack is installed, you can resume system operation or start your system and use the system normally.

2

1

1 Battery release switch

2 Battery pack

Figure 2-2 Removing the Battery Pack

38

Image 40

Contents

According to FCC Part Y l i s t i c L T 8 0 0 P T a b l e t Table of Contents Care and Maintenance Preface Y l i s t i c L T 8 0 0 P T a b l e t About This Guide Conventions Used in the GuideLimited Warranty Information Service and SupportFujitsu Contact Information Fujitsu OnlineGetting Started Y l i s t i c L T 8 0 0 P T a b l e t Getting to Know Your Tablet In-box ItemsOptional Accessories Peripheral/Accessory Fujitsu Part NumberStylistic LT800P Tablet Features Stylistic LT800P Tablet Features Front ViewFront / Top / Left Features Stylistic LT800P Tablet Features Rear View Rear / Bottom / Right Features Status Display Status Display IconsSystem Status Indicators Mode/State LED State RemarksBattery RAMHovering Connectors and Peripheral Interfaces Left-Side Connectors and InterfacesPeripheral Connectors/Interfaces ConnectorPurpose PeripheralCommunication is about 3 feet, and within Additional System Icons Using the Stylistic LT800P Tablet Y l i s t i c L T 8 0 0 P T a b l e t Using Your Stylistic LT800P System StatesPower Icon Current State To Change State Appearance Changing System StatesShutting Down the System Powering Up the TabletSuspending System Operation Power icon is blinking Suspend-to-RAMmode Down the system rather than using Suspend-to-RAM mode Resuming System Operation Using Hotpads Stylistic Hotpad ArraysHotpad Keys IconIcon Name Description Using the Pen Calibrating the penTo Calibrate the Pen Charging the Battery Pack Using Hovering ModeReplacing the Pen Removing and Installing the Battery Pack Battery Pack Charging Time90% 100%Removing the Battery Pack Tips for Conserving Battery Power Operation of the Bridge BatteryChanging the Bios Settings Modem ConnectionPC Card Slot LAN Port RJ-45Starting Bios Setup Y l i s t i c L T 8 0 0 P T a b l e t Care and Maintenance Y l i s t i c L T 8 0 0 P T a b l e t Caring for Your Stylistic LT800P Protecting the Display ScreenStoring the Stylistic LT800P Tablet Avoiding OverheatingTroubleshooting Y l i s t i c L T 8 0 0 P T a b l e t Display Screen Is Blank or Difficult to Read System Will Not Resume OperationInfrared Data Transfer Is Not Working Audio Volume Too Low Configuring Peripherals InterfacesCursor Is Not Tracking Pen Tablet Is Not Responding to the PenHardware Specifications Y l i s t i c L T 8 0 0 P T a b l e t Stylistic LT800P Hardware Specifications Stylistic LT800P Tablet SpecificationsInterface Specifications Stylistic LT800P Tablet Specifications Power Specifications Environmental SpecificationsAgency Approval Specifications Additional SpecificationsY l i s t i c L T 8 0 0 P T a b l e t Agency Notices Y l i s t i c L T 8 0 0 P T a b l e t Agency Notices Y l i s t i c L T 8 0 0 P T a b l e t DOC Industry Canada Notices Y l i s t i c L T 8 0 0 P T a b l e t UL Notice Y l i s t i c L T 8 0 0 P T a b l e t Appendix Y l i s t i c L T 8 0 0 P T a b l e t Wireless LAN, Health and Authorization for use FCC Regulatory InformationRegulatory Notes and Statements Regulatory Information/DisclaimersFCC Radio Frequency Exposure statement FCC Interference StatementExport restrictions Before Using This Device Characteristics of the DeviceWireless LAN Modes Using this Device AdHoc ModeHow to Handle This Device Infrastructure ModeSetting Parameters Connecting Windows 2000 SystemsWorkflow Table A-1 Profile Parameters DescriptionTable A-2 Encryption Key Setup WEPTCP/IP Settings Network SettingsNetwork Connection Windows Table A-3 Setting an IP Address Checking the full computer name and workgroupSharing Setting File and Printer Sharing for Microsoft NetworksTable A-4 Checking computer name and workgroup Sharing Files Printer Sharing Table A-5 Sharing filesTable A-6 Printer Sharing Accessing Another Computer Checking the ConnectionChecking the Connectivity Table A-7 Checking connectivityConnecting Windows XP Systems Table A-8 Setting parameters Table A-9 Setting an IP address Network SettingsNetwork Connection Table A-10 Setting computer name and workgroup SharingSetting File and Printer Sharing for Microsoft Networks Checking the Connection Table A-11 Checking connectivity Troubleshooting Table TroubleshootingProblem Possible Cause Possible Solution Signal Retry the connection Where directory and filename repre If the connection is successful Problem Possible Solution WindowsWindows XP Setting IP Addresses About IP AddressesSpecifications Technical Specifications for Integrated Wireless LAN DeviceY l i s t i c L T 8 0 0 P T a b l e t Index Y l i s t i c L T 8 0 0 P T a b l e t Items included with, 9 Stylistic LT P-867 Specifications Y l i s t i c L T 8 0 0 P T a b l e t 100