Zebra Technologies zebra p330 Printing a Test Card, Packing the P330i Printer for Shipment

Page 35

Installation and Setup

Printing a Test Card

Printing a Test Card

With ribbon and cards loaded, your P330i Printer is ready to print. To check the operation of the printer, you should print a test card. (Printing a test card does not require that the printer be connected to your computer or network, but power must be applied.)

1.Set the printer’s power switch (on the back of the printer) to the OFF ( O ) position.

2.While pressing the Printer’s front panel button (next to the LCD display panel), switch the printer ON ( ).

3.Hold the panel button until the LCD display panel reads “SELF TEST”.

4.Release the panel button, and the test card will print.

This is an example of the test card:

PLASTIC CARD PRINTER

PRINTER: P330iM

Serial N°: XXXXX

Firmware: XXXXXXX

300 dpi

TEST CARD

Head resistance: XXXX

Offset: XXXX-XXXX

EC:XX

Printing counter: XXXXX

Packing the P330i Printer for Shipment

If the P330i Printer is to be shipped, it is important to use the original packing and shipping material to prevent damage to the Printer. If the original material is lost, a replacement Shipping Kit can be ordered from Zebra; please refer to the Media List on the Windows Drivers and User Documentation CD supplied with this printer.

Note • The specifics of the shipment and the printer’s condition may influence which of the following steps are followed; common sense should prevail.

1.Remove cards in the card feeder:

a.While the printer still has power applied and is turned on, and is still connected to the host computer, remove cards from the card feeder. The last card may be difficult to remove. If so, use the Eject Card command available through the driver on the host computer to eject the last card that is staged in the feeder.

Caution • Do not physically pull the last card out of the feeder staging area. This could damage the printer and void the warranty, as well as damage the card.

b.Close the Card Feeder Cover.

980459-001 Rev. A

P330i User’s Manual

23

Image 35
Contents User’s Manual Page Foreword Return Materials AuthorizationPrinters Warranty InformationCopyright Notice TrademarksSpare Parts Product Disposal Declarations of ConformitySupplemental Information Smart Card Options P330i Printer ModelIcons Table of Contents Troubleshooting Appendix C Connecting to a Network Xii P330i User’s Manual Introduction Printer FeaturesControls, Connectors, and Indicators Print Head Open LCD PanelIntroduction General Information Installation and SetupUnpacking the Printer Installation and SetupUnpacking the Printer CD-ROM with Driver Wizard Print Head Carriage Latch Installing the P330i Print Driver Loading a Ribbon Take-up Spool Flange Supply Spool Installation and Setup Installing the Card Cleaning Cartridge Close the printer’s Main Cover Setting the Card Thickness Control Card Thickness Control Loading Cards Installation and Setup Card Output Hopper Connecting the Printer to your Computer Connecting Power Packing the P330i Printer for Shipment Printing a Test CardPacking the P330i Printer for Shipment Printing a Card Setting Printer PropertiesPrinting a Sample Card Feeding One Card at a Time Printing a Card When to Clean CleaningCleaning the Printer How to Clean Cleaning the Print Head How To Replace the Cleaning Roller Card Cleaning CartridgeWhen to Replace the Cleaning Roller Cleaning Replace the Card Cleaning Cartridge into the printer Troubleshooting Head Open message Print Quality Issues Troubleshooting Troubleshooting Troubleshooting Ethernet Adapter Status Indicator Troubleshooting the Ethernet Connection and AdapterResetting to Factory Defaults Network Status/Activity Indicator Card Specifications Technical SpecificationsGeneral Specifications Ribbon SpecificationsFonts Card DimensionsBar Codes Environmental Mechanical SpecificationsBi-Directional Communications Interfaces ElectricalOptions Media Loading Orientation Magnetic Card Stripe EncoderIntroduction Sample Encoding Program Magnetic Encoder CleaningISO Standard Encoding Magnetic Card Stripe Encoder Smart Card Contact Station DB-9 Pin Smart Card Contact Points Smart Card Contact Station InterfacePrinter Sharing Connecting to a NetworkInternal Print Server External Print Server