Zebra Technologies Strata Thermal Printers manual We Need To Hear From You

Page 4

WARRANTY INFORMATION

We Need To Hear From You!

To Establish Your Warranty Period And Provide Access To Technical Support,

Send Us Your Product Registration Card Today!

Zebra warrants the mechanism, control electronics and power supply, under normal use and ser- vice, to be free from defects in material and workmanship for a period of twelve (12) months from the date of purchase by the end user. Zebra warrants the print head, under normal use and service, to be free from defects in material and workmanship for a period of ninety (90) days or 30KM of printing (whichever occurs first) from the date of purchase by the end user. Proof of purchase or product registration is required. If proof of purchase or product registration cannot be established, shipment date to the original buyer (dealer or distributor) will be used to establish the warranty pe- riod.

Failure to exercise caution to protect the equipment from electrostatic discharge damage, adverse temperature and humidity conditions or physical abuse may void the warranty. Failure to use only Zebra approved media may void the warranty. Zebra will, at its option, repair or replace the equip- ment or any parts which are determined to be defective within this warranty period, and which are returned to Zebra F.O.B. factory of origin.

The warranty set forth above is exclusive and no other warranty, whether written or oral, is ex- pressed or implied. Zebra specifically disclaims the implied warranties of merchantability and fit- ness for a particular purpose.

RETURN MATERIALS AUTHORIZATION

Before returning any equipment to Zebra for in warranty or out of warranty repair, contact Repair Administration for a Return Materials Authorization (RMA) number. Repack the equipment in the original packing material and mark the RMA number clearly on the outside. Ship the equipment, freight prepaid, to the address listed below:

Zebra Repair Administration, USA

1001 Flynn Road

Camarillo, CA. 93012

Phone: +1 (805) 579-1800

FAX: +1 (805) 579-1808

Label Printers:

Card Printers:

Zebra International, Europe

Zebra International, Europe

Eltron House

Zone Indutrielle, Rue d'Amsterdam

Molly Millars Lane

44370 Varades, France

Wokingham RG41 2QZ England

Phone: +33 (0) 240 097 070

Phone: +44 (0) 1189 770 300

FAX: +33 (0) 240 834 745

FAX: +44 (0) 1189 895 762

 

iv

980181-001 Rev.C

Image 4
Contents Strata Page Foreword Return Materials Authorization We Need To Hear From YouTable of Contents General Cautions and Warnings Media Cautions & Tips Viii Installation Check List 1 Printer Check Voltage Step ➊ Attach Power= Off Step ➋ Attach Interface Cable Parallel Interface Serial InterfaceStep ➌ Apply Power = OnSoftware Operation Your Printer Ribbon Take-up Spindle Sensor Guide Bar Bracket Operation Operation Status Indicator Loading Labels or Tags Correct Incorrect Operation Operation Media Guides Release Lever Operation Operation Move the media roll to the lower media stand for printing Step Adjustment Wheel Sensor Position MarkerSensor Position Operation Windows Users Take-Up Spindles Supply Tracking Bar Loading Transfer RibbonsNotch Long Spoke Notch Operation Operation Operation Removing a Partially Used Transfer Ribbon Top Of Form Sensing Dump Mode Sample Printout Operation Operation Cleaning the Print Head Cleaning Under Sensor BracketUsing the Label Dispenser Remove slack by pulling the liner Operation Appendix a Troubleshooting Common Printing Problems Troubleshooting Guide Check for Out-of-Media condition or missing Internet Serial Interface Communication Configuration Serial Interface Cable WiringPrint Tag Media SensingDirection Appendix B Printer Features Hardware Options Accessories General Specifications Bar Codes Code Software and DriversPostnet Ribbons Communications InterfacePrinter Features Appendix C Supplies and Accessories Thermal Retail applications where labels are 980181-001 Rev.C Appendix D Using the Media Cutter Specifications Cutter warranty Using the Media Cutter Clear the Jam Use tweezers to remove media from the internal blade areasReplace the Cutter Check the Cutter World Wide Offices Zebra Technologies Corporation Eltron Products