Transcend Information TS2G-8GCF266 manual Word 91 Advanced power management level value

Page 64

TS2G~8GCF266

266X CompactFlash Card

 

 

 

￿Word 91: Advanced power management level value

Bits 7-0 of word 91 contain the current Advanced Power Management level setting.

￿Word 128: Security Status Bit 8: Security Level

If set to 1, indicates that security mode is enabled and the security level is maximum. If set to 0 and security mode is enabled, indicates that the security level is high.

Bit 5: Enhanced security erase unit feature supported

If set to 1, indicates that the Enhanced security erase unit feature set is supported. Bit 4: Expire

If set to 1, indicates that the security count has expired and Security Unlock and Security Erase Unit are command aborted until a power-on reset or hard reset.

Bit 3: Freeze

If set to 1, indicates that the security is Frozen. Bit 2: Lock

If set to 1, indicates that the security is locked. Bit 1: Enable/Disable

If set to 1, indicates that the security is enabled. If set to 0, indicates that the security is disabled. Bit 0: Capability

If set to 1, indicates that CompactFlash Storage Card supports security mode feature set.

If set to 0, indicates that CompactFlash Storage Card does not support security mode feature set.

￿Word 160: Power Requirement Description

This word is required for CompactFlash Storage Cards that support power mode 1.

Bit 15: VLD

If set to 1, indicates that this word contains a valid power requirement description.

If set to 0, indicates that this word does not contain a power requirement description. Bit 14: RSV

This bit is reserved and shall be 0. Bit 13: -XP

If set to 1, indicates that the CompactFlash Storage Card does not have Power Level 1 commands. If set to 0, indicates that the CompactFlash Storage Card has Power Level 1 commands

Bit 12: -XE

If set to 1, indicates that Power Level 1 commands are disabled. If set to 0, indicates that Power Level 1 commands are enabled. Bit 0-11: Maximum current

This field contains the CompactFlash Storage Card’s maximum current in mA.

￿Word 162: Key Management Schemes Supported Bit 0: CPRM support

If set to 1, the device supports CPRM Scheme (Content Protection for Recordable Media) If set to 0, the device does not support CPRM.

Bits 1-15 are reserved for future additional Key Management schemes.

￿Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings

This word describes the capabilities and current settings for CFA defined advanced timing modes using the True IDE interface.

Notice! The use of True IDE PIO Modes 5 and above or of Multiword DMA Modes 3 and above impose significant restrictions on the implementation of the host:

Additional Requirements for CF Advanced Timing Modes.

There are four separate fields defined that describe support and selection of Advanced PIO timing modes and Advanced Multiword DMA timing modes. The older modes are reported in words 63 and 64.

Transcend Information Inc.

64

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Dimensions Placement FeaturesDescription Transcend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification Output Drive Type Output Drive Characteristics Signal Interface TS2G~8GCF266266X CompactFlash Card Pull-up pin 45 BVD2 to avoid sensing their batteries as LowSeries termination required for Ultra DMA operation Ultra DMA Electrical RequirementsTable Typical Series Termination for Ultra DMA Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS2G~8GCF266 Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS2G~8GCF266 Output Write Timing Specification TS2G~8GCF266 True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst TimingTS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Single Function CF+ Cards Card ConfigurationMultiple Function CF+ Cards Table CF+ Card Configuration Registers Decoding Table CF+ Card Register and Memory Space DecodingAttribute Memory Function Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS2G~8GCF266 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer FunctionCommon Memory Transfer Function Table Common Memory FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingTrue IDE Mode Addressing Memory Mapped AddressingCF-ATA Registers Data Register Address 1F0h170hOffset 0,8,9Feature Register Address 1F1h171h Offset 1, 0Dh Write Only Sector Count Register Address 1F2h172h OffsetSector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetTS2G~8GCF266 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set Check Power Mode 98h or E5h Execute Drive Diagnostic 90h Erase Sectors C0hFlush Cache E7h Format Track 50hIdentify Device Ech TS2G~8GCF266 Word 0 General Configuration Word 1 Default Number of Cylinders Word 3 Default Number of HeadsWord 6 Default Number of Sectors per Track Word 49 Capabilities Bit 13 Standby TimerMultiple Sector Setting Total Sectors Addressable in LBA ModeTranslation Parameters Valid Current Number of Cylinders, Heads, Sectors/TrackWords 82-84 Features/command sets supported Word 65 Minimum Multiword DMA transfer cycle timeRecommended Multiword DMA transfer cycle time Word 68 Minimum PIO transfer cycle time with IordyWords 85-87 Features/command sets enabled Word 88 Ultra DMA Modes Supported and Selected Word 89 Time required for Security erase unit completionWord 91 Advanced power management level value Word 160 Power Requirement DescriptionWord 128 Security Status Bit 8 Security Level Additional Requirements for CF Advanced Timing ModesTS2G~8GCF266 Idle 97h or E3h Initialize Drive Parameters 91h Idle Immediate 95h or E1hNOP 00h Read Buffer E4h Read DMA C8h Read Long Sector 22h or 23hTS2G~8GCF266 Recalibrate 1Xh Request Sense 03h Seek 7Xh Set Features EFh Feature Supported TS2G~8GCF266 Standby Immediate 94h or E0h Translate Sector 87h Translate Sector InformationWear Level F5h Write Buffer E8h Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 Error Posting Smart Command Set Smart Feature Register Values Smart Command SetS. Table Capacity Smart Data Structure Decription
Top Page Image Contents