Transcend Information TS2G-8GCF266 manual Smart Data Structure, Decription

Page 80

TS2G~8GCF266		266X CompactFlash Card

SMART Data Structure

		BYTE			F / V			Decription
		0-1			X			Revision code
		2-361			X			Vendor specific
		362			V			Off line data collection status
		363			X			Self-test execution status byte
		364-365			V			Total time in seconds to complete off-line data collection activity
		366			X			Vendor specific
		367			F			Off-line data collection capability
		368-369			F			SMART capability
								Error logging capability
		370			F			7-1 Reserved
		370			F			0 1=Device error logging supported
								0 1=Device error logging supported
		371			X			Vendor specific
		372			F			Short self-test routine recommended polling time (in minutes)
		373			F			Extended self-test routine recommended polling time (in minutes)
		374			F			Conveyance self-test routine recommended polling time (in minutes)
		375-385			R			Reserved
		386-395			F			Date Code
		396			V			Number of MU in device (0~n)
		397+(n*6)			V			MU number
		398+(n*6)			V			MU data block
		400+(n*6)			V			MU spare block
		401+(n*6)			V			Init. Bad block
		402+(n*6)			V			Last Defect Bad block ( Newest state)
		511			V			Data structure checksum

F=the content of the byte is fixed and does not change.

V=the content of the byte is variable and may change depending on the state of the device or

the commands executed by the device.

X=the content of the byte is vendor specific and may be fixed or variable.

R=the content of the byte is reserved and shall be zero.

* 4 Byte value : [MSB] [2] [1] [LSB]

Above technical information is based on CFA standard data and tested to be reliable. However, Transcend makes no warranty, either expressed or implied, as to its accuracy and assumes no liability in connection with the use of this product. Transcend reserves the right to make changes in specifications at any time without prior notice.

Transcend Information Inc.

80

Image 80

Contents Description Placement FeaturesDimensions Transcend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification Output Drive Type Output Drive Characteristics Signal Interface TS2G~8GCF266266X CompactFlash Card Pull-up pin 45 BVD2 to avoid sensing their batteries as LowTable Typical Series Termination for Ultra DMA Ultra DMA Electrical RequirementsSeries termination required for Ultra DMA operation Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS2G~8GCF266 Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS2G~8GCF266 Output Write Timing Specification TS2G~8GCF266 True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst TimingTS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Multiple Function CF+ Cards Card ConfigurationSingle Function CF+ Cards Table CF+ Card Configuration Registers Decoding Table CF+ Card Register and Memory Space DecodingAttribute Memory Function Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS2G~8GCF266 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer FunctionCommon Memory Transfer Function Table Common Memory FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingTrue IDE Mode Addressing Memory Mapped AddressingCF-ATA Registers Data Register Address 1F0h170hOffset 0,8,9Feature Register Address 1F1h171h Offset 1, 0Dh Write Only Sector Count Register Address 1F2h172h OffsetSector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetTS2G~8GCF266 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set Check Power Mode 98h or E5h Execute Drive Diagnostic 90h Erase Sectors C0hFlush Cache E7h Format Track 50hIdentify Device Ech TS2G~8GCF266 Word 0 General Configuration Word 1 Default Number of Cylinders Word 3 Default Number of HeadsWord 6 Default Number of Sectors per Track Word 49 Capabilities Bit 13 Standby TimerMultiple Sector Setting Total Sectors Addressable in LBA ModeTranslation Parameters Valid Current Number of Cylinders, Heads, Sectors/TrackWords 82-84 Features/command sets supported Word 65 Minimum Multiword DMA transfer cycle timeRecommended Multiword DMA transfer cycle time Word 68 Minimum PIO transfer cycle time with IordyWords 85-87 Features/command sets enabled Word 88 Ultra DMA Modes Supported and Selected Word 89 Time required for Security erase unit completionWord 91 Advanced power management level value Word 160 Power Requirement DescriptionWord 128 Security Status Bit 8 Security Level Additional Requirements for CF Advanced Timing ModesTS2G~8GCF266 Idle 97h or E3h NOP 00h Idle Immediate 95h or E1hInitialize Drive Parameters 91h Read Buffer E4h Read DMA C8h Read Long Sector 22h or 23hTS2G~8GCF266 Recalibrate 1Xh Request Sense 03h Seek 7Xh Set Features EFh Feature Supported TS2G~8GCF266 Standby Immediate 94h or E0h Translate Sector 87h Translate Sector InformationWear Level F5h Write Buffer E8h Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 Error Posting S. Table Capacity Smart Command SetSmart Command Set Smart Feature Register Values Smart Data Structure Decription