Transcend Information TS2G-8GCF266 manual Feature Supported

Page 72

TS2G~8GCF266		266X CompactFlash Card

	Feature Supported

Features 01h and 81h are used to enable and clear 8 bit data transfer modes in True IDE Mode. If the 01h feature command is issued all data transfers shall occur on the low order D[7:0] data bus and the -IOIS16 signal shall not be asserted for data register accesses. The host shall not enable this feature for DMA transfers.

Features 02h and 82h allow the host to enable or disable write cache in CompactFlash Storage Cards that implement write cache. When the subcommand disable write cache is issued, the CompactFlash Storage Card shall initiate the sequence to flush cache to non-volatile memory before command completion.

Feature 03h allows the host to select the PIO or Multiword DMA transfer mode by specifying a value in the Sector Count register. The upper 5 bits define the type of transfer and the low order 3 bits encode the mode value. One PIO mode shall be selected at all times. For Cards which support DMA, one Multiword DMA mode shall be selected at all times. The host may change the selected modes by the Set Features command.

Transcend Information Inc.

72

Image 72

Contents Placement Features DimensionsDescription Transcend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification Output Drive Type Output Drive Characteristics Signal Interface TS2G~8GCF266266X CompactFlash Card Pull-up pin 45 BVD2 to avoid sensing their batteries as LowUltra DMA Electrical Requirements Series termination required for Ultra DMA operationTable Typical Series Termination for Ultra DMA Ultra DMA Mode Cabling Requirement Attribute Memory Read Timing Specification TS2G~8GCF266 Common Memory Read Timing Specification Common Memory Write Timing Specification Input Read Timing Specification TS2G~8GCF266 Output Write Timing Specification TS2G~8GCF266 True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst TimingTS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Card Configuration Single Function CF+ CardsMultiple Function CF+ Cards Table CF+ Card Configuration Registers Decoding Table CF+ Card Register and Memory Space DecodingAttribute Memory Function Attribute Memory FunctionConfiguration Option Register Base + 00h in Attribute Memory TS2G~8GCF266 Pin Replacement Register Base + 04h in Attribute Memory Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer FunctionCommon Memory Transfer Function Table Common Memory FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Primary and Secondary Address Configurations Table Primary and Secondary I/O DecodingContiguous I/O Mapped Addressing Table Contiguous I/O DecodingTrue IDE Mode Addressing Memory Mapped AddressingCF-ATA Registers Data Register Address 1F0h170hOffset 0,8,9Feature Register Address 1F1h171h Offset 1, 0Dh Write Only Sector Count Register Address 1F2h172h OffsetSector Number LBA 7-0 Register Address 1F3h173h Offset Cylinder Low LBA 15-8 Register Address 1F4h174h OffsetTS2G~8GCF266 Device Control Register Address 3F6h376h Offset Eh Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set Check Power Mode 98h or E5h Execute Drive Diagnostic 90h Erase Sectors C0hFlush Cache E7h Format Track 50hIdentify Device Ech TS2G~8GCF266 Word 0 General Configuration Word 1 Default Number of Cylinders Word 3 Default Number of HeadsWord 6 Default Number of Sectors per Track Word 49 Capabilities Bit 13 Standby TimerMultiple Sector Setting Total Sectors Addressable in LBA ModeTranslation Parameters Valid Current Number of Cylinders, Heads, Sectors/TrackWords 82-84 Features/command sets supported Word 65 Minimum Multiword DMA transfer cycle timeRecommended Multiword DMA transfer cycle time Word 68 Minimum PIO transfer cycle time with IordyWords 85-87 Features/command sets enabled Word 88 Ultra DMA Modes Supported and Selected Word 89 Time required for Security erase unit completionWord 91 Advanced power management level value Word 160 Power Requirement DescriptionWord 128 Security Status Bit 8 Security Level Additional Requirements for CF Advanced Timing ModesTS2G~8GCF266 Idle 97h or E3h Idle Immediate 95h or E1h Initialize Drive Parameters 91hNOP 00h Read Buffer E4h Read DMA C8h Read Long Sector 22h or 23hTS2G~8GCF266 Recalibrate 1Xh Request Sense 03h Seek 7Xh Set Features EFh Feature Supported TS2G~8GCF266 Standby Immediate 94h or E0h Translate Sector 87h Translate Sector InformationWear Level F5h Write Buffer E8h Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 Error Posting Smart Command Set Smart Command Set Smart Feature Register ValuesS. Table Capacity Smart Data Structure Decription