American Power Conversion 100 VAC Mount the UPS in the Rack, Load the UPS into the Rack

Page 9

Mount the UPS in the Rack

Select a location with adequate air flow that is free from excessive dust. Ensure that the air vents on the front and rear of the UPS are not blocked. Allow at least 2.54 cm (1 inch) of space on both sides.

The UPS requires two people to install due to its weight.

To lighten the UPS, you may remove the batteries while you mount the unit in the rack. Refer to Replacing the Battery, page 15, for instructions on removing the batteries.

The UPS comes with standard 46.5-cm (19-inch) rack mount brackets (ears) and cleats installed and mounting rails for rack mounting included. The rails support the UPS and allow adequate air flow. There are two steps to install the UPS in a rack. This section describes each in detail.

1.Install the mounting rails in the rack (required for four-post racks only).

2.Load the UPS into the rack.

Check the rack to make sure it will not tip after moving the mounting brackets.

Install the Mounting Rails in the Rack (Four-Post Rack Installation Only)

Install the mounting rails in the rack. Directions are included with the rail kit.

Load the UPS into the Rack

Due to the weight of the UPS, two people are required to install it in the rack. To lighten the UPS, you may remove the batteries while you mount it in the rack. Refer to Replacing the Battery, page 16, for instructions on how to remove the batteries.

Four-Post Racks

1. Supporting the UPS from both sides, carefully align the unit with the rails.

2. Each side of the UPS has a cleat Πthat must slide into the groove on the rail. Insert each cleat into its groove and slide the UPS into position.

3. Insert the four (4) ornamental screws

Œ

supplied with the UPS through the

 

 

mounting brackets and into the top

 

and bottom holes in the U-space.

5

990-7096 Rev. 2

Page 8 Page 10
Image 9
Page 8 Page 10
Contents User’s Manual 1400 VA 2U Rack Mount Uninterruptible Power Supply 100 VacPage Table of Contents English Maintenance and Troubleshooting Handling Safety Safety InformationElectrical Safety Conventions Used in this ManualDeenergizing Safety Battery SafetyRecycling of Batteries Basics How to Contact APCAbout APC About Your New UPSInstallation How to Install Your Smart-UPSUnpacking Mount the UPS in the Rack Load the UPS into the RackFour-Post Racks Connect the Battery and Attach the Front Panel Bezel Two-Post RacksRemoving the UPS from the Rack Turn on the UPS Connect Power and Equipment to the UPS990-7096 Rev Front Panel OperationOperation Self-TestUtility Power Battery Power Computer Interface Port Rear PanelTvss Screw Voltage SensitivityLow Battery Warning Level On-Battery OperationFunction Factory User Selectable Description Default Choices User Configuration ItemsReplacing the Battery Maintenance and TroubleshootingStorage Storage Conditions990-7096 Rev Troubleshooting Condition Display Beeper Some or all front panel indicators are flashingService and Transport On-Battery Run Time Regulatory Agency ApprovalsLoad Run Time Watts Minutes Limited Warranty

100 VAC specifications

American Power Conversion (APC), a leading global provider of power management solutions, offers a range of products that cater to the evolving needs of consumers and businesses alike. Among its extensive product line, the APC 100 VAC model stands out as an essential component for maintaining reliable power for sensitive electronic equipment.

The APC 100 VAC is engineered to deliver stable voltage and reliable power to various devices, making it ideal for both residential and commercial environments. One of its core features is its capacity to regulate voltage levels, ensuring that sensitive equipment operates within specified parameters. This feature helps prevent damage caused by voltage fluctuations, which could otherwise lead to equipment failure or downtime.

Another distinguishing characteristic of the APC 100 VAC is its built-in surge protection. The unit is designed to guard connected devices against voltage spikes that occur due to lightning strikes or power outages. By diverting excess voltage away from sensitive components, the APC 100 VAC helps prolong equipment life and maintain operational efficiency.

In terms of technology, the APC 100 VAC is equipped with advanced monitoring capabilities. Users can easily track power usage, voltage levels, and overall system performance through an intuitive user interface. This technology not only aids in proactive maintenance but also empowers users to optimize their power consumption, leading to cost savings over time.

Moreover, the APC 100 VAC features a compact and sleek design, which allows it to fit seamlessly into various spaces without causing clutter. Its lightweight structure makes installation and portability hassle-free, catering to users who may need to relocate their devices frequently.

Additionally, the model integrates a variety of connectivity options, including USB and serial ports, enabling it to connect with different types of devices for enhanced functionality. This versatility makes the APC 100 VAC valuable for a range of applications, from home offices to data centers.

In summary, the American Power Conversion 100 VAC model is a robust solution for managing power needs. Its voltage regulation, surge protection, advanced monitoring technology, compact design, and connectivity options establish it as a standout choice for those seeking enhanced power management. Whether for personal or commercial use, the APC 100 VAC is poised to deliver unparalleled reliability and performance.
Top Page Image Contents