BIXOLON Official Driver Guide for F310 Printer - Cash Drawer Specifications
Page 30

SRP-F310/312

3-6 Cash Drawer Specifications

3-6-1 Drawer Cable

Ferrite Core: 1 turn (OP-18E: 18.2 x 12.5 x 25.5)

Figure 3-11 Drawer Cable

3-6-2 Cable Connection

Pin No.

Description

Direction

1

Frame GND

-

2

Drawer Kick-Out Driver Signal #1

Output

3

Drawer Open / Close Signal

Input

4

+24V

-

5

Drawer Kick-Out Driver Signal #2

Output

6

Signal GND

-

 

Table 3-21 Drawer Cable Connection

 

※Note: +24V is always output through pin 4 during power on.

Rev. 1.00

- 30 -

Page 29 Page 31
Image 30
Page 29 Page 31
Contents SRP-F310/312 SRP-F310/312 Remaining Roll Paper Adjustment Precaution Segment Safety PrecautionsServicing Precaution Precaution for Electrostatically Sensitive Devices ESDs Operational PrecautionsInterface Cable Installation InstallationAC Adapter Installation USB Cable InstallationCover Open Installation Ethernet Cable InstallationDongleUsb A-Type Cable Installation Paper Roll InstallationSetting the DIP switch IEEE1284 Parallel, USB Interface Setting the DIP switchesSetting the DIP switch RS-232C Serial Interface ※ Auto Cutter Enable / Disable selectionSelf Test Mode Hexadecimal Dumping10 The Self-Test Sheet Setting the Memory Switches MSW1MSW2 MSW3 BXL/POSMSW4 MSW6 OFF SHIFT-JIS BIG5MSW5 MSW11Printer Dimensions mm AC Adapter Dimensions mmAppearance Ethernet Feature Locations-SRP-F310/312USB B-TYPE SmpsGeneral Specifications RAMUSB Character Specification Thermal Printer SpecificationsPrinter Specification SRP-F310 TPH KRB-72-7TA02-BIX2,KYOCERA Corporation※ Note Paper SpecificationReliability and Environment Specification McbfTPH Thermal Printer Head Specification Printable AreaOther Component Specification ALL-HIGHSmps Output Connector Smps SpecificationsSmps Switching Mode Power Supply Specification GNDXON/XOFF Interface Specifications1 RS-232C Serial Interface 1a Specification 1b RS-232C I/F CablePrinter Host 1d Signal Description1c Cable Connection Side 9P1f S/W Flow Control 2a Forward Mode Specification Compatibility mode1e H/W Flow Control IEEE1284 Parallel Interface2c Signal Specification Compatibility/Nibble/Byte mode 2c IEEE1284 I/F Cable3 USB2.0 Interface 3a Specification3b Signal Description 3c CableUSB Cable 4d Construction10 illustrates the keyed connector protocol Series a Connectors Series B ConnectorsCash Drawer Specifications Drawer CableCable Connection Ethernet Specifications EthernetWlan WPA/WPA2TKIP/AES-CCMP PSKWiring Diagram HardwareBlock Diagram Rev SRP-F310/312 SRP-F310/312 SRP-F310/312 Block Diagram IEEE1284 Logic IC Driving Voltage +5VDC Power CircuitSpecial Circuit Descriptions CPU A/D, USB core and OSC Voltage +2.5VDCReset Circuit Fpga core Voltage +1.5VDCCPU core Voltage +1.2VDC Buzzer and Cash Drawer Circuits Buzzer Driving Circuit Cash Drawer Driving CircuitPBA MD0 4 I/F PBA Detect Block Diagram5 RS-232C Communication Block Diagram MD1 MD2Parallel Communication Block Diagram USB Communication Block DiagramDIP Switch Circuit STB2 Thermal Printer Head CircuitSTB1 CPUDisassembly and Assembly Case lower blockSRP-F310/312 SRP-F310/312 Case Upper block ③SPRING HingeSRP-F310/312 SRP-F310/312 Frame block ②HOUSING P-END Adjustment Remaining Roll Paper AdjustmentMaintenance Troubleshooting Troubleshooting flow chartPower LED does not light Paper and Error led blink Paper and Error led lit Paper led lit Error led blink Error led lit Self test is not normal Data from host is not printed normally OK?YES NoendPower Problem Printing Quality Problems Printer Mechanism Problems Auto Cut Mechanism Problems
Top Page Image Contents