Agilent Technologies N-Series user manual Returning the Printer to Operation

Page 16

Page 2-16

User’s Manual

figure 2.2

CAUTION: DO NOT press the X/TRA XLi on to the controller board at an angle, or interface pins could be bent, damaging the unit and causing it to not function properly.

▲Align the screw holes on the mounting bracket of the XLi with the notches on the interface port. Make sure the mounting bracket is flush with the interface port.

▲Fasten mounting screws to the printer through the guiding holes on either side of the X/TRA XLi.

Returning the Printer to Operation

▲Slide the controller board back into the printer, aligning the edge of the board in the guide rails

▲Push the controller board firmly into place. Make certain that there is no space between the controller board and the printer chassis. They must be flush.

▲Turn the thumbscrews clockwise to tighten. Do not use tools to tighten, only finger pressure.

▲Connect the X/TRA XLi parallel interface to the standard Centronics parallel connection on the printer. Lock into

Image 16

Contents Agile Revision date 5 NovemberRelease Notes Copyright InformationUser’s Manual About This Manual FCC/DOC Statement Table of Contents Reset Printers SupportedForms and Graphics Support Conversion MethodsOperator Text Message Tabs HorizontalXtraedit Configuration Configure Menu Install Settings Now Alt-I Install As New Configuration Specifications Features and OptionsGeneral Information Firmware upgrades via provided PC/MSDOS software Two-year product warranty512K Flash Standard 256K RAM Toll-free tech support is available from 730 AM. to 4 PM Prior to Installation Selecting a Location Electrical Requirements Operating EnvironmentN17 Installation Package ContentsUnpacking Printer PreparationInserting the X/TRA XLi N17Returning the Printer to Operation N24/N32/N40 Installation Place with wire latches Reconnect power cordInserting the X/TRA XLi Returning the Printer to Operation Connection Test ConnectionsTRA XLi Connection to Parallel Input If Printer does not Start TroubleshootingIf the Printer does not Return a Status Sheet TRA XLi XES Features and Specifications Introduction to XESForms downloading Vector graphics Raster graphics Xerox DocuPrint N17, N24, N32, N40Titan10iso Titan12iso XCP14iso PC/MS DOS menu-driven configuration program Xtraedit Xerox Data Monitor Mode emulation Configuration/StatusXES Commands User-Defined KeysEmulation Change Selecting a UDK46Page User’s Manual XES Command Format Job Control CommandsJob Control Commands Non-Job Control Commands Two Types of Escape SequencesConfiguration/Status Non-Job Control CommandsLine Endings 48Page User’s ManualJob Boundary Commands Optional CommentCommand s+Xd Print JobPrint Job Mixed Orientation Page410 User’s ManualMiscellaneous Commands Print Multiple Copies CollatedPrint Multiple Copies Non-Collated Paper TrayOutput Tray OffsetDuplex Start Duplex Invert StartDuplex Side Select Duplex StopComment Font Commands Font LoadFont Unload Font AddFormatting Commands Font ID AssignmentFont Change Units 1/60Command szf Command smH,T,B,L,Rd Range See chartUnits 1/300 MarginsMargin Top Margin BottomMargin Left Margin RightCommand st#1,#2,...#64d Command sdTabs Clear Horizontal Page418 User’s ManualCommand sv#1,#2,...#64d Command seTabs Vertical Tabs Clear VerticalJustification Stop Justification StartJustification Unlimited Command sq Command si# RangeCenter Line SpacingCommand sip#d Command sqzs#CdLine Spacing Absolute Character Spacing AbsoluteForms Creation Commands Baseline Placement AbsoluteText Placement Absolute Command sza#1,#2dtextd Range See BelowText Placement Relative Command srC1#C2 Range See BelowPage424 User’s Manual Portrait Landscape For up For down For left For rightDocument Enhancement Commands Command sxor yX,Y,L,W,Sd Range See BelowCommand sb Line Draw X or YBold Stop Overstrike StartOverstrike Stop Subscript StartSub/Superscript Stop Superscript StartUnderline Start Underline Stop Merge Page LoadMerge Page Unload Form ID AssignmentForm Merge Start CycleformsForm Merge Stop Merge StartCommand szd Merge StopGraphic Window Page430 User’s ManualGraphic Delete Graphic Window RepeatGraphic Line Graphic ArcPage432 User’s Manual Range T=1-15Command sgbTX1,Y1,X2,Y2d Range See Below Graphic Pie ChartGraphic Box Load Translation Table Character ReassignmentLanguage Command s+D Data MonitorContol Codes Page436 User’s ManualLoading Xtraedit Getting StartedAbout Xtraedit Select Port Page538 User’s ManualXtraedit Configuration Xtraedit Main ScreenF10=Menu Keyboard CommandsPage540 User’s Manual Esc=Cancel/Previous Menu Other Keyboard CommandsEnter=OK/Select Item Alt-X=ExitXLI Resources Directory File MenuPage542 User’s Manual Configure Menu Exit Alt-XSelect Configuration to Edit Page54 User’s ManualChange Default Configuration Text Generation Page546 User’s ManualFont Selection Font RotationLanguage Character SetLine Spacing Absolute Line SpacingPrinter Setup Page548 User’s ManualInput Tray Selection Input Paper SizeOutput Tray Selection Input Tray MapOutput Tray Map Two-up Printing Page5-0 User’s ManualSource Code Duplex Length Portrait, LandscapeSize Correction Page5-2 User’s ManualTop Offset Minimum Top Coordinate Left OffsetMinimum Left Coordinate Page5-4 User’s Manual Margins Portrait, LandscapeTop Margin Tabs Portrait, Landscape Bottom MarginLeft Margin Right MarginPage5-6 User’s Manual Page5-7 Other Options Page5-8 User’s ManualEmulation Mode Line EndUppercase Commands Job TimeoutUnits of Measure UDK CharacterInstall Settings Now Alt-I Undo Settings Alt-UError Level Install As New Configuration Delete ConfigurationResources Menu Page562 User’s ManualView Installed Fonts Load FontPage564 User’s Manual Non-Shrinkable Fonts Delete FontLoad Resources File Command Line Interface Save Resources to FilePack XLI Memory Page56 User’s ManualPreferences Menu Measurement Units for EntriesConfirm Before Updating XLI Page568 User’s ManualContents Help Menu