Agilent Technologies N-Series user manual Emulation Mode, Line End

Page 80

XTRAEDIT CONFIGURATION

Page5-9

26

Emulation Mode

This option enables the user to set the configuration either to XES Mode or to Passthrough Mode. XES Mode is the normal operating mode of the XLI, enabling XES documents to be printed to the user’s PCL5 printer. Passthrough Mode enables the user to print other document types, including PCL5 documents, and PostScript documents if the user’s printer supports PostScript.

The emulation mode being used will be indicated by the XLI LED, either 0 for XES Mode (normal operating mode), or P for Passthrough Mode. The default is XES Mode for Configurations 0, 1, 2 and 3. The default for Configurations 4, 5, 6 and 7 is Passthrough Mode.

Line End

XES protocol requires that certain printer commands are terminated with a line ending, either a carriage return only (CR), a line feed only (LF) or both (CR/LF). The type of line ending is defined by the user. This option enables the user to indicate to the XLI which type of line ending is being used in the user’s XES documents to terminate XES commands.

The user can select CR/LF, CR only, LF only or Auto CR/LF. Auto CR/LF is the default, and it tells the XLI to accept any line ending as an XES command terminator.

Image 80

Contents Agile Revision date 5 NovemberUser’s Manual Copyright InformationRelease Notes About This Manual FCC/DOC Statement Table of Contents Reset Printers SupportedForms and Graphics Support Conversion MethodsOperator Text Message Tabs HorizontalXtraedit Configuration Configure Menu Install Settings Now Alt-I Install As New Configuration General Information Features and OptionsSpecifications Firmware upgrades via provided PC/MSDOS software Two-year product warranty512K Flash Standard 256K RAM Toll-free tech support is available from 730 AM. to 4 PMPrior to Installation Selecting a LocationElectrical Requirements Operating EnvironmentN17 Installation Package ContentsUnpacking Printer PreparationInserting the X/TRA XLi N17Returning the Printer to Operation N24/N32/N40 Installation Place with wire latches Reconnect power cordInserting the X/TRA XLi Returning the Printer to Operation TRA XLi Connection to Parallel Input ConnectionsConnection Test If the Printer does not Return a Status Sheet TroubleshootingIf Printer does not Start TRA XLi XES Features and Specifications Introduction to XESTitan10iso Titan12iso XCP14iso Xerox DocuPrint N17, N24, N32, N40Forms downloading Vector graphics Raster graphics PC/MS DOS menu-driven configuration program Xtraedit Xerox Data Monitor Mode emulation Configuration/StatusXES Commands User-Defined KeysEmulation Change Selecting a UDK46Page User’s Manual XES Command Format Job Control CommandsJob Control Commands Non-Job Control Commands Two Types of Escape SequencesConfiguration/Status Non-Job Control CommandsLine Endings 48Page User’s ManualJob Boundary Commands Optional CommentCommand s+Xd Print JobPrint Job Mixed Orientation Page410 User’s ManualMiscellaneous Commands Print Multiple Copies CollatedPrint Multiple Copies Non-Collated Paper TrayOutput Tray OffsetDuplex Start Duplex Invert StartComment Duplex StopDuplex Side Select Font Commands Font LoadFont Unload Font AddFormatting Commands Font ID AssignmentFont Change Units 1/60Command szf Command smH,T,B,L,Rd Range See chartUnits 1/300 MarginsMargin Top Margin BottomMargin Left Margin RightCommand st#1,#2,...#64d Command sdTabs Clear Horizontal Page418 User’s ManualCommand sv#1,#2,...#64d Command seTabs Vertical Tabs Clear VerticalJustification Unlimited Justification StartJustification Stop Command sq Command si# RangeCenter Line SpacingCommand sip#d Command sqzs#CdLine Spacing Absolute Character Spacing AbsoluteForms Creation Commands Baseline Placement AbsoluteText Placement Absolute Command sza#1,#2dtextd Range See BelowText Placement Relative Command srC1#C2 Range See BelowPage424 User’s Manual Portrait Landscape For up For down For left For rightDocument Enhancement Commands Command sxor yX,Y,L,W,Sd Range See BelowCommand sb Line Draw X or YBold Stop Overstrike StartOverstrike Stop Subscript StartUnderline Start Superscript StartSub/Superscript Stop Underline Stop Merge Page LoadMerge Page Unload Form ID AssignmentForm Merge Start CycleformsForm Merge Stop Merge StartCommand szd Merge StopGraphic Window Page430 User’s ManualGraphic Delete Graphic Window RepeatGraphic Line Graphic ArcPage432 User’s Manual Range T=1-15Graphic Box Graphic Pie ChartCommand sgbTX1,Y1,X2,Y2d Range See Below Language Character ReassignmentLoad Translation Table Command s+D Data MonitorContol Codes Page436 User’s ManualAbout Xtraedit Getting StartedLoading Xtraedit Select Port Page538 User’s ManualXtraedit Configuration Xtraedit Main ScreenPage540 User’s Manual Keyboard CommandsF10=Menu Esc=Cancel/Previous Menu Other Keyboard CommandsEnter=OK/Select Item Alt-X=ExitPage542 User’s Manual File MenuXLI Resources Directory Configure Menu Exit Alt-XSelect Configuration to Edit Page54 User’s ManualChange Default Configuration Text Generation Page546 User’s ManualFont Selection Font RotationLanguage Character SetLine Spacing Absolute Line SpacingPrinter Setup Page548 User’s ManualInput Tray Selection Input Paper SizeOutput Tray Map Input Tray MapOutput Tray Selection Source Code Page5-0 User’s ManualTwo-up Printing Duplex Length Portrait, LandscapeTop Offset Page5-2 User’s ManualSize Correction Minimum Left Coordinate Left OffsetMinimum Top Coordinate Top Margin Margins Portrait, LandscapePage5-4 User’s Manual Tabs Portrait, Landscape Bottom MarginLeft Margin Right Margin Page5-6 User’s Manual Page5-7 Other Options Page5-8 User’s ManualEmulation Mode Line EndUppercase Commands Job TimeoutUnits of Measure UDK CharacterError Level Undo Settings Alt-UInstall Settings Now Alt-I Install As New Configuration Delete ConfigurationResources Menu Page562 User’s ManualView Installed Fonts Load FontPage564 User’s Manual Load Resources File Delete FontNon-Shrinkable Fonts Command Line Interface Save Resources to FilePack XLI Memory Page56 User’s ManualPreferences Menu Measurement Units for EntriesConfirm Before Updating XLI Page568 User’s ManualContents Help Menu