Agilent Technologies N-Series Document Enhancement Commands, Line Draw X or Y, Bold Start

Page 46

XES COMMANDS

Page425-

Line Draw (X or Y)

▲COMMAND: sx(or y)X,Y,L,W,Sd

▲ RANGE: See Below

To draw a line parallel to the x (short edge) axis, enter:

sxX,Y,L,W,Sd

To draw a line parallel to the y (long edge) axis, enter:

syX,Y,L,W,Sd

where X and Y specify the starting point of the line, where L is the length of the line expressed in dots, where W is the width of the line expressed in dots (with a value between 1 and 31), and where S is the line shading (any value between 0 and 15 is accepted, where 15 is solid black).

For example, if the user would like to draw a line on a portrait orientation page, parallel to the y axis, that starts 1.75" over from the x origin and 0.25" up from the y origin, and that is 6.0" long and 1/50" wide:

sy525,75,1800,6d

The page orientation is determined by the first font on the page, so be certain to specify a font before using this command.

To draw a line on a landscape orientation page, parallel to the x axis, that starts 5.0" down from the x origin and 1.5" over from the y origin, and that is 4.0" long and 1/100" wide:

sx1500,150,1200,3d

Document Enhancement Commands

This section describes the commands for bolding, underlining, overstriking, subscripting and superscripting text.

Bold Start

▲COMMAND: sb

▲RANGE: N/A

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Agile Revision date 5 NovemberRelease Notes Copyright InformationUser’s Manual About This Manual FCC/DOC Statement Table of Contents Forms and Graphics Support ResetPrinters Supported Conversion MethodsOperator Text Message Tabs HorizontalXtraedit Configuration Configure Menu Install Settings Now Alt-I Install As New Configuration Specifications Features and OptionsGeneral Information 512K Flash Standard 256K RAM Firmware upgrades via provided PC/MSDOS softwareTwo-year product warranty Toll-free tech support is available from 730 AM. to 4 PMElectrical Requirements Prior to InstallationSelecting a Location Operating EnvironmentUnpacking N17 InstallationPackage Contents Printer PreparationInserting the X/TRA XLi N17Returning the Printer to Operation N24/N32/N40 Installation Place with wire latches Reconnect power cordInserting the X/TRA XLi Returning the Printer to Operation Connection Test ConnectionsTRA XLi Connection to Parallel Input If Printer does not Start TroubleshootingIf the Printer does not Return a Status Sheet TRA XLi XES Features and Specifications Introduction to XESForms downloading Vector graphics Raster graphics Xerox DocuPrint N17, N24, N32, N40Titan10iso Titan12iso XCP14iso PC/MS DOS menu-driven configuration program Xtraedit Xerox Data Monitor Mode emulation Configuration/StatusXES Commands User-Defined KeysEmulation Change Selecting a UDK46Page User’s Manual Job Control Commands Non-Job Control Commands XES Command FormatJob Control Commands Two Types of Escape SequencesLine Endings Configuration/StatusNon-Job Control Commands 48Page User’s ManualJob Boundary Commands Optional CommentPrint Job Mixed Orientation Command s+XdPrint Job Page410 User’s ManualPrint Multiple Copies Non-Collated Miscellaneous CommandsPrint Multiple Copies Collated Paper TrayDuplex Start Output TrayOffset Duplex Invert StartDuplex Side Select Duplex StopComment Font Unload Font CommandsFont Load Font AddFont Change Formatting CommandsFont ID Assignment Units 1/60Units 1/300 Command szfCommand smH,T,B,L,Rd Range See chart MarginsMargin Left Margin TopMargin Bottom Margin RightTabs Clear Horizontal Command st#1,#2,...#64dCommand sd Page418 User’s ManualTabs Vertical Command sv#1,#2,...#64dCommand se Tabs Clear VerticalJustification Stop Justification StartJustification Unlimited Center Command sqCommand si# Range Line SpacingLine Spacing Absolute Command sip#dCommand sqzs#Cd Character Spacing AbsoluteText Placement Absolute Forms Creation CommandsBaseline Placement Absolute Command sza#1,#2dtextd Range See BelowPage424 User’s Manual Portrait Landscape Text Placement RelativeCommand srC1#C2 Range See Below For up For down For left For rightCommand sb Document Enhancement CommandsCommand sxor yX,Y,L,W,Sd Range See Below Line Draw X or YOverstrike Stop Bold StopOverstrike Start Subscript StartSub/Superscript Stop Superscript StartUnderline Start Merge Page Unload Underline StopMerge Page Load Form ID AssignmentForm Merge Stop Form Merge StartCycleforms Merge StartGraphic Window Command szdMerge Stop Page430 User’s ManualGraphic Delete Graphic Window RepeatPage432 User’s Manual Graphic LineGraphic Arc Range T=1-15Command sgbTX1,Y1,X2,Y2d Range See Below Graphic Pie ChartGraphic Box Load Translation Table Character ReassignmentLanguage Command s+D Data MonitorContol Codes Page436 User’s ManualLoading Xtraedit Getting StartedAbout Xtraedit Select Port Page538 User’s ManualXtraedit Configuration Xtraedit Main ScreenF10=Menu Keyboard CommandsPage540 User’s Manual Enter=OK/Select Item Esc=Cancel/Previous MenuOther Keyboard Commands Alt-X=ExitXLI Resources Directory File MenuPage542 User’s Manual Configure Menu Exit Alt-XSelect Configuration to Edit Page54 User’s ManualChange Default Configuration Font Selection Text GenerationPage546 User’s Manual Font RotationLine Spacing LanguageCharacter Set Absolute Line SpacingInput Tray Selection Printer SetupPage548 User’s Manual Input Paper SizeOutput Tray Selection Input Tray MapOutput Tray Map Two-up Printing Page5-0 User’s ManualSource Code Duplex Length Portrait, LandscapeSize Correction Page5-2 User’s ManualTop Offset Minimum Top Coordinate Left OffsetMinimum Left Coordinate Page5-4 User’s Manual Margins Portrait, LandscapeTop Margin Left Margin Tabs Portrait, LandscapeBottom Margin Right MarginPage5-6 User’s Manual Page5-7 Other Options Page5-8 User’s ManualEmulation Mode Line EndUnits of Measure Uppercase CommandsJob Timeout UDK CharacterInstall Settings Now Alt-I Undo Settings Alt-UError Level Resources Menu Install As New ConfigurationDelete Configuration Page562 User’s ManualView Installed Fonts Load FontPage564 User’s Manual Non-Shrinkable Fonts Delete FontLoad Resources File Pack XLI Memory Command Line InterfaceSave Resources to File Page56 User’s ManualPreferences Menu Measurement Units for EntriesConfirm Before Updating XLI Page568 User’s ManualContents Help Menu

N-Series specifications

Agilent Technologies N-Series is a sophisticated family of next-generation instruments designed primarily for analytical and measurement applications in laboratories and industrial environments. The N-Series comprises a range of devices tailored for diverse sectors, including chemical analysis, life sciences, and material sciences. This series is recognized for its high precision, versatility, and advanced technological integration.

One of the key features of the N-Series is its exceptional performance in measurement accuracy and reliability. Utilizing state-of-the-art sensors and algorithms, these instruments deliver precise results, enabling users to conduct sensitive analyses with confidence. The N-Series also incorporates advanced automation capabilities, allowing for increased throughput and reduced human error during testing processes.

The N-Series benefits from innovative technologies such as digital signal processing and connectivity options, which enhance data acquisition and analysis capabilities. By employing cutting-edge algorithms, these devices can process complex data sets efficiently, providing comprehensive insights into various samples' characteristics. The integration of connectivity features, including USB and Ethernet connectivity, allows seamless communication with external devices, facilitating data sharing and remote monitoring.

Moreover, the N-Series is designed with user experience in mind. These instruments come equipped with intuitive interfaces, simplifying operation and enhancing user navigation. The touch-screen displays offer easy access to functions, while the built-in software provides advanced analytical tools and customizable reporting options. This focus on user-friendliness ensures that both experienced professionals and new users can operate the devices with ease.

Another notable characteristic of the N-Series is its robust construction and reliability under challenging conditions. Built to withstand demanding laboratory environments, these instruments demonstrate resilience, ensuring long-term performance and reduced downtime.

In summary, Agilent Technologies N-Series stands out as a leading solution in analytical instrumentation, providing users with advanced technology, exceptional accuracy, and user-friendly operation. Its comprehensive features cater to diverse measurement needs across various scientific fields, making it an invaluable tool for researchers and industry professionals alike. The ongoing evolution of the N-Series reflects Agilent's commitment to innovation and excellence in analytical solutions, paving the way for more precise and efficient laboratory work worldwide.
Top Page Image Contents