Agilent Technologies N-Series user manual Job Boundary Commands, Optional Comment

Page 30

XES COMMANDS

49Page-

occurs. The Configuration/Status Page is printed if the command is followed immediately by a comma (,) or if an error is detected either during the print job or during powerup.

The X/TRA XLi enables the user to determine the conditions in which a Configuration/Status Page will be printed. Refer to Section 5 — XTRAEDIT Configuration for information on specifying the conditions in which a Configuration/Status Page will be printed.

The Configuration/Status Page includes the following information:

▲The error number and error type, if any errors were detected

▲The names of any simulated, resident or downloaded fonts

▲The names of any downloaded forms

▲An optional comment, if one was entered

▲The current configuration

A sample Configuration/Status Page can be found in Section 6 — Service and Reference.

Optional Comment

An optional comment will be printed on the Configuration/Status Page if a comment was entered directly after the comma in the XES command line that triggered the Configuration/Status Page. The comma is a request for printing a Configuration/Status Page. Whether or not this request is honored can be determined by setting a parameter using XTRAEDIT. The comment can be up to 132 characters in length.

The comment will always be printed by the XLi if a Configuration/Status Page is printed.

Job Boundary Commands

A job boundary is a command function that tells the printer where the job begins and ends, and it tells the printer what type of data the job contains. The command to start printing a document is the “Print Job” command.

The command to end a document is the “Reset” command.

Image 30

Contents Agile Revision date 5 NovemberCopyright Information Release NotesUser’s Manual About This Manual FCC/DOC Statement Table of Contents Forms and Graphics Support ResetPrinters Supported Conversion MethodsOperator Text Message Tabs HorizontalXtraedit Configuration Configure Menu Install Settings Now Alt-I Install As New Configuration Features and Options SpecificationsGeneral Information 512K Flash Standard 256K RAM Firmware upgrades via provided PC/MSDOS softwareTwo-year product warranty Toll-free tech support is available from 730 AM. to 4 PMElectrical Requirements Prior to InstallationSelecting a Location Operating EnvironmentUnpacking N17 InstallationPackage Contents Printer PreparationInserting the X/TRA XLi N17Returning the Printer to Operation N24/N32/N40 Installation Place with wire latches Reconnect power cordInserting the X/TRA XLi Returning the Printer to Operation Connections Connection TestTRA XLi Connection to Parallel Input Troubleshooting If Printer does not StartIf the Printer does not Return a Status Sheet TRA XLi XES Features and Specifications Introduction to XESXerox DocuPrint N17, N24, N32, N40 Forms downloading Vector graphics Raster graphicsTitan10iso Titan12iso XCP14iso PC/MS DOS menu-driven configuration program Xtraedit Xerox Data Monitor Mode emulation Configuration/StatusXES Commands User-Defined KeysEmulation Change Selecting a UDK 46Page User’s Manual Job Control Commands Non-Job Control Commands XES Command FormatJob Control Commands Two Types of Escape SequencesLine Endings Configuration/StatusNon-Job Control Commands 48Page User’s ManualJob Boundary Commands Optional CommentPrint Job Mixed Orientation Command s+XdPrint Job Page410 User’s ManualPrint Multiple Copies Non-Collated Miscellaneous CommandsPrint Multiple Copies Collated Paper TrayDuplex Start Output TrayOffset Duplex Invert StartDuplex Stop Duplex Side SelectComment Font Unload Font CommandsFont Load Font AddFont Change Formatting CommandsFont ID Assignment Units 1/60Units 1/300 Command szfCommand smH,T,B,L,Rd Range See chart MarginsMargin Left Margin TopMargin Bottom Margin RightTabs Clear Horizontal Command st#1,#2,...#64dCommand sd Page418 User’s ManualTabs Vertical Command sv#1,#2,...#64dCommand se Tabs Clear VerticalJustification Start Justification StopJustification Unlimited Center Command sqCommand si# Range Line SpacingLine Spacing Absolute Command sip#dCommand sqzs#Cd Character Spacing AbsoluteText Placement Absolute Forms Creation CommandsBaseline Placement Absolute Command sza#1,#2dtextd Range See BelowPage424 User’s Manual Portrait Landscape Text Placement RelativeCommand srC1#C2 Range See Below For up For down For left For rightCommand sb Document Enhancement CommandsCommand sxor yX,Y,L,W,Sd Range See Below Line Draw X or YOverstrike Stop Bold StopOverstrike Start Subscript StartSuperscript Start Sub/Superscript StopUnderline Start Merge Page Unload Underline StopMerge Page Load Form ID AssignmentForm Merge Stop Form Merge StartCycleforms Merge StartGraphic Window Command szdMerge Stop Page430 User’s ManualGraphic Delete Graphic Window RepeatPage432 User’s Manual Graphic LineGraphic Arc Range T=1-15Graphic Pie Chart Command sgbTX1,Y1,X2,Y2d Range See BelowGraphic Box Character Reassignment Load Translation TableLanguage Command s+D Data MonitorContol Codes Page436 User’s ManualGetting Started Loading XtraeditAbout Xtraedit Select Port Page538 User’s ManualXtraedit Configuration Xtraedit Main ScreenKeyboard Commands F10=MenuPage540 User’s Manual Enter=OK/Select Item Esc=Cancel/Previous MenuOther Keyboard Commands Alt-X=ExitFile Menu XLI Resources DirectoryPage542 User’s Manual Configure Menu Exit Alt-XSelect Configuration to Edit Page54 User’s ManualChange Default Configuration Font Selection Text GenerationPage546 User’s Manual Font RotationLine Spacing LanguageCharacter Set Absolute Line SpacingInput Tray Selection Printer SetupPage548 User’s Manual Input Paper SizeInput Tray Map Output Tray SelectionOutput Tray Map Page5-0 User’s Manual Two-up PrintingSource Code Duplex Length Portrait, LandscapePage5-2 User’s Manual Size CorrectionTop Offset Left Offset Minimum Top CoordinateMinimum Left Coordinate Margins Portrait, Landscape Page5-4 User’s ManualTop Margin Left Margin Tabs Portrait, LandscapeBottom Margin Right MarginPage5-6 User’s Manual Page5-7 Other Options Page5-8 User’s ManualEmulation Mode Line EndUnits of Measure Uppercase CommandsJob Timeout UDK CharacterUndo Settings Alt-U Install Settings Now Alt-IError Level Resources Menu Install As New ConfigurationDelete Configuration Page562 User’s ManualView Installed Fonts Load FontPage564 User’s Manual Delete Font Non-Shrinkable FontsLoad Resources File Pack XLI Memory Command Line InterfaceSave Resources to File Page56 User’s ManualPreferences Menu Measurement Units for EntriesConfirm Before Updating XLI Page568 User’s ManualContents Help Menu