Toshiba TLP-B2 owner manual Enlarging the picture size, Press Zoom +

Page 32

Enlarging the picture size

CONTENTS

32

You can enlarge the picture size projected.

 

 

ZOOM

 

Press ZOOM (+).

 

 

 

 

 

 

+ Each time the ZOOM (+) button is pressed, the

 

 

 

 

enlargement ratio increases.

 

 

ZOOM

 

To decrease the enlargement ratio, press the ZOOM (–)

ENTER

 

+

 

enlarged.

 

 

 

 

button.

 

 

 

 

Pressing / / / buttons shifts the picture part

Press the RESET button to cancel the zoom operation.

RESET

Notes

Picture enlargement display will return to the normal size after the power turns off and on again.

Some signals cannot be applicable for the enlargement operation.

The picture may not be projected properly while shifting the picture.

Since the electrical digital zoom system is employed, the picture quality may be degraded in accordance with the enlargement ratio.

If you perform other operation, the zoom operation is cancelled.

Operations

Image 32
Contents TLP-B2ultra U Safety Precautions Before useImportant Precautions Important Safety Instructions Important Safety Instructions HeatUse Object and Liquid EntryCoin-shaped Battery Damage Requiring Service Power supply cord selection Contents Foot adjuster Names of each part on the main unitControl connector RS-232C Speaker Exhaust holes AC in socketCT -90038ZOOM Loading a battery Push back the holderRemote control operation Front side Rear sideFloor-mounted projector placement Translucent screen ViewerSide view Determine the screen size projected on the screenTop view Push both sides of the lens cover to take off Connect the power cordTake off the lens cover Projector placement angle adjustment HeightTurn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Ceiling-mounted front projectionCeiling-mounted rear projection Translucent screenCONTROLRS-232CRGB S-VIDEOAUDIOVIDEO Connecting a Macintosh computer CONTROLRS-232CRGB S-VIDEOAUDIOVIDEOConnecting video equipment CONTROLRS-232CRGB S-VIDEOAUDIOVIDEOProjector operation control by a computer CONTROLRS-232CRGB S-VIDEOAUDIOVIDEOPlayback mode Projection on the screenPress ON/STANDBY OperationsSelect the input source On the remote control, press RGB or VideoProjection on the screen Focusing ring Zooming ringFocus on the picture by turning Turn to the right to enlarge the pictureTurning the power off Off, unplug the power cordProjector Press ON/STANDBY again Correcting the keystone distortion KEY Press KeystoneCutting off the picture and sound temporarily Press MuteFreezing the picture Press FreezeEnlarging the picture size Press Zoom +Adjustments Menu screen structureQuick menu Used frequentlyQuick menu setting Adjust the item by pressingPress Menu Press EnterScreen changes to the full menu screen Quick menu settingMenu screen disappears Adjusting picture Picture adjustment Select the setting item ContrastPressing Adjustments Display the full menu screenAdjusting picture If you adjust other setting item, return to stepAdjusting Image Image adjustment Adjusting image Menu button will return to the previous setting screenPosition To shift the image down -, to up + Clock To remove vertical stripesAdjusting RGB-level Level adjustment Level by pressingAdjusting RGB-level EnterAdjusting audio output Audio adjustment Select, Output select by pressingAdjusting audio output Adjust the Volume by pressingPress Menu several times until the full Channel selectSetting the input signal Signal setting Mode, No signal background, No signalPower off by pressing Then press Setting screen for the item selected appearsPicture mode Video modeNo signal background No signal power offSetting the input signal Setting the display method Display setting Select by pressing / and then press EnterPosition, Menu background color, On Screen display by pressing / and thenSetting the display method Change the selection by pressingMenu position Menu background colorDefault setting Default setting Projection modePower on LanguageMenu Display the current operation status Reset, Status display Data settingStatus display Keystone reset Reset, Status displayFactory reset mode Maintenance On indicatorTrouble indications Lamp turns off or does not light upAir filter cleaning Unplug the power cord Take off the air filter coverClean the air filter cover Attach the air filter cover MaintenanceLens and main unit cleaning Cleaning the lensCleaning the main unit Replacing the intake, exhaust fans and air filterLamp replacement Unplug the power cord Wait until the lamp gets cold enoughTake off the lamp cover on the bottom panel Pull out the lampAttach the lamp cover Maintenance Reset the lamp timerLoad a new lamp Before calling service personal OthersSignal assignment for RGB input Pin arrangementsApplicable RGB signal Timing chartControlling the projector by using RS-232C Interface format Command listControlling the projector by using RS-232C Specifications Main unitAccessories Limited Warranty Toshiba TLP-B2 Series 3LCD Data ProjectorLimited Warranty