Toshiba TLP-B2 owner manual Lens and main unit cleaning, Cleaning the lens, Cleaning the main unit

Page 56

Lens and main unit cleaning

CONTENTS

56

CAUTION

If you use the projector mounted on the ceiling, ask the dealer to carry out the maintenance such as cleaning.

Cleaning the lens

Use a blower or a lens cleaner to clean the lens.

Never rub or tap the lens with a hard object as the lens surface is fragile.

Cleaning the main unit

Pull out the power cord before cleaning.

Use a soft cloth to wipe off stains from the

surface.

• To remove difficult stains, use a soft cloth slightly moistened with a weak solution of synthetic detergent and water, and finish with a soft, dry cloth.

Replacing the intake, exhaust fans and air filter

To maintain the efficiency of the projector, replace the intake and exhaust fans about every two to three years.

Ask the dealer for the replacement.

Maintenance

Image 56
Contents TLP-B2ultra U Safety Precautions Before useImportant Precautions Important Safety Instructions Important Safety Instructions HeatUse Object and Liquid EntryCoin-shaped Battery Damage Requiring Service Power supply cord selection Contents Foot adjuster Names of each part on the main unitControl connector RS-232C Speaker Exhaust holes AC in socketCT -90038ZOOM Loading a battery Push back the holderRemote control operation Front side Rear sideFloor-mounted projector placement Translucent screen ViewerSide view Determine the screen size projected on the screenTop view Push both sides of the lens cover to take off Connect the power cordTake off the lens cover Projector placement angle adjustment HeightTurn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Ceiling-mounted front projectionCeiling-mounted rear projection Translucent screenCONTROLRS-232CRGB S-VIDEOAUDIOVIDEO Connecting a Macintosh computer CONTROLRS-232CRGB S-VIDEOAUDIOVIDEOConnecting video equipment CONTROLRS-232CRGB S-VIDEOAUDIOVIDEOProjector operation control by a computer CONTROLRS-232CRGB S-VIDEOAUDIOVIDEOPlayback mode Projection on the screenPress ON/STANDBY OperationsSelect the input source On the remote control, press RGB or VideoProjection on the screen Focusing ring Zooming ringFocus on the picture by turning Turn to the right to enlarge the pictureTurning the power off Off, unplug the power cordProjector Press ON/STANDBY againCorrecting the keystone distortion KEY Press KeystoneCutting off the picture and sound temporarily Press MuteFreezing the picture Press FreezeEnlarging the picture size Press Zoom +Adjustments Menu screen structureQuick menu Used frequentlyQuick menu setting Adjust the item by pressingPress Menu Press EnterScreen changes to the full menu screen Quick menu settingMenu screen disappears Adjusting picture Picture adjustment Select the setting item ContrastPressing Adjustments Display the full menu screenAdjusting picture If you adjust other setting item, return to stepAdjusting Image Image adjustment Adjusting image Menu button will return to the previous setting screenPosition To shift the image down -, to up + Clock To remove vertical stripesAdjusting RGB-level Level adjustment Level by pressingAdjusting RGB-level EnterAdjusting audio output Audio adjustment Select, Output select by pressingAdjusting audio output Adjust the Volume by pressingPress Menu several times until the full Channel selectSetting the input signal Signal setting Mode, No signal background, No signalPower off by pressing Then press Setting screen for the item selected appearsPicture mode Video modeNo signal background No signal power offSetting the input signal Setting the display method Display setting Select by pressing / and then press EnterPosition, Menu background color, On Screen display by pressing / and thenSetting the display method Change the selection by pressingMenu position Menu background colorDefault setting Default setting Projection modePower on LanguageMenu Display the current operation status Reset, Status display Data settingStatus display Keystone reset Reset, Status display Factory reset mode Maintenance On indicatorTrouble indications Lamp turns off or does not light upAir filter cleaning Unplug the power cord Take off the air filter coverClean the air filter cover Attach the air filter cover MaintenanceLens and main unit cleaning Cleaning the lensCleaning the main unit Replacing the intake, exhaust fans and air filterLamp replacement Unplug the power cord Wait until the lamp gets cold enoughTake off the lamp cover on the bottom panel Pull out the lampAttach the lamp cover Maintenance Reset the lamp timerLoad a new lamp Before calling service personal OthersSignal assignment for RGB input Pin arrangementsApplicable RGB signal Timing chartControlling the projector by using RS-232C Interface format Command listControlling the projector by using RS-232C Specifications Main unitAccessories Limited Warranty Toshiba TLP-B2 Series 3LCD Data ProjectorLimited Warranty