Toshiba B-852 owner manual Environment, How to enter the System Mode

Page 27

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.9 Setting an Operating Environment

2.9 Setting an Operating Depending on the settings of your host computer or an interface to be used, it may be necessary to change the printer parameter settings.

Environment

LCD Message Display

 

 

 

 

 

FEED key

 

PAUSE key

 

 

 

RESTART key

 

 

 

Follow the procedures described below to change the printer parameter settings in the System Mode to correspond to your environment.

NOTE:

Incorrect settings can cause the printer to function erroneously. If you have any problems with the parameter settings, please contact your nearest TOSHIBA TEC service representative.

For the settings this manual does not cover, please contact your nearest TOSHIBA TEC service representative, or refer to the B-852 Series Key Operation Specification.

How to enter the System Mode

1.Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display.

2.Press the [PAUSE] key to pause the printer.

3.Hold down the [RESTART] key for three seconds until “<1>RESET” is displayed.

ON LINE

[PAUSE]

PAUSE

Hold down [RESTART] for 3 sec.

<1>RESET

[FEED] [RESTART]

<2>PARAMETER SET

[FEED] [RESTART]

<3>ADJUST SET

[FEED] [RESTART]

<4>DUMP MODE

[FEED] [RESTART]

<5>EXPAND MODE

[FEED] [RESTART]

<6>AUTO CALIB

[FEED] [RESTART]

<7>LAN

[FEED] [RESTART]

<8>RTC SET

[FEED] [RESTART]

The System Mode consists of the following menus.

<1>RESET

This menu is used to clear print data sent from a

 

PC and return the printer to an idle state.

 

Refer to Section 3.3 Reset.

<2>PARAMETER SET

This menu is used to set the printer parameters.

 

Refer to Section 2.9.1 Parameter Setting.

<3>ADJUST SET

This menu is used to make a fine adjustment of a

 

print start position, cut position, etc.

 

Refer to Section 2.12 Position and Print Tone

 

Fine Adjustment.

<4>DUMP MODE

This menu is used to print the data in the receive

 

buffer for debug.

 

Refer to Section 2.9.2 Dump Mode Setting.

<5>EXPAND MODE

This menu is used to start the program for

 

BASIC mode.

 

Refer to Section 2.9.3 BASIC Expansion

 

Mode.

<6>AUTO CALIB

This menu is used to enable or disable the

 

automatic calibration function.

 

Refer to Section 2.9.4 Automatic Caliburation.

<7>LAN

This menu is used to enable or disable the LAN

 

communication and SNMP.

 

Refer to Section 2.9.5 LAN Setting.

<8>RTC SET

This menu is used to set the date and time of the

 

real time clock, enable or disable the low battery

 

check, and choose a real time renewal timing.

 

Refer to Section 2.9.6 Real Time Clock

 

Setting.

NOTES:

1.System Mode menus can be selected with the [RESTART] or [FEED] key.

2.To enter each of the above System Mode menus, press the [PAUSE] key when the menu is displayed.

3.If the [PAUSE] key is pressed with “<1>RESET” being displayed, the printer will turn to an idle state and the message will change to “ONLINE”

E2-14

Image 27
Contents Series Vorsicht CE Compliance for EU onlySeries Waste Recycling information for users Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA1-1 E3-1E4-1 E5-1Introduction Features Product OverviewUnpacking Accessories Dimensions AppearanceFront View Rear View Interior Operation PanelOption Name Type Description OptionsManual threshold setting Printer SetupSetup Flow ProcedureInstallation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Power Cord Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder UnitLoading the Media Straight and true through the printerSpacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterEnvironment How to enter the System ModeSequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayedAfter selecting a character code, press the Pause key Character Zero SelectionCharacter Code Selection Use the Feed or Restart key to select a desired optionAfter selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length SelectionStop Bit Length Selection Parity SelectionFlow Control Code Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait SelectionFeed key Control Code SelectionAfter selecting the Feed key function, press the Pause key Feed Key Function SelectionAfter selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code SelectionAfter selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing SelectionWeb Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Expansion I/O Interface Type Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Maxi Code Specification Selection Label End/Ribbon End SelectionAfter selecting a Label End type, press the Pause key After selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing methodData in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length When the Pause key is pressed, Basic program is executed Basic Expansion ModeNot activated Activated Feed gap sensor Black mark sensor LAN Setting Time Setting Date SettingReal Time Clock Setting 3 Low Battery Check Setting RTC Data Renewal Timing SettingCont IP Address Setting TCP/IP Feed and Pause keys This parameter is to set a Gateway IP address Printer IP AddressThis parameter is to set an IP address Gateway IP AddressSubnet Mask This parameter is to set a Subnet MaskSocket Port This parameter is to set a Dhcp client ID This parameter is to enable DhcpDhcp Dhcp Client IDDhcp Host Name This parameter is to set a Dhcp host nameAscii code and Hex. code correspondence table Installing the Printer Drivers IntroductionGeneral Description Parallel Interface Installing the Printer DriverWindows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using an optional Cutter Module Threshold Fine Adjustment Feed gap sensor Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine AdjustmentWhen setting +0.0 mm After selecting a fine adjustment value, press the Pause keyPosition and Print Tone Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Select the sensor to be adjusted by using the Feed keyLower Black Mark Sensor/Feed Gap Sensor Adjustment No media Upper Black Mark Sensor AdjustmentLower Black Mark Sensor Adjustment Feed Gap Sensor Adjustment„ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds Feed Gap Sensor Used to restart printing On Line ModeOperation Panel Used to stop printing temporarilyPress and hold the Restart key for 3 seconds or longer Operation ResetMaintenance CleaningPrint Head/Platen/ Sensors Optional Cutter Module Covers and PanelsSolutions TroubleshootingError Messages Error Messages Problems/CausesError Messages Problems/Cause Media has run outRestart key Possible Problems Causes Possible ProblemsClean the Cutter Blade Load the ribbon properlyAttach the Cutter Cover properly Remove the jammed paper Removing Jammed Media Printer Specifications This section describes the printer specificationsModel 852-TS22-QQ-R 852-TS22-QP-R Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media TypeDetection Area of the Reflective Sensor Detection Area of the Transmissive SensorFigure below shows the effective print area on the media Effective Print AreaRibbon Recommended Media and Ribbon TypesMedia type Description Media type Vellum paper and label Care/Handling of the Media and RibbonRibbon type Description Combination of Media and RibbonAppendix 1 Messages and Leds Symbols in the messageDhcp Client is being initialised Command error has occurredAnalyzing the command 100BASE LAN is being initialisedFollowing message appears Parallel interface Centronics Appendix 2 InterfaceConnector LED status Link LED Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 StandardSerial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits JAN8, EAN8 MSI Interleaved 2NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digits CODE39 Full AsciiCustomer bar code of high priority QR code UPC-A+2 digitsUPC-A+5 digits Industrial 2 Data MatrixAppendix 4 Glossaries USB Universal Serial Bus See Black mark sensorMedia and ribbon See Feed gap sensor3-1, A1-1 IndexIndex EO1-33055D
Related manuals
Manual 2 pages 62.15 Kb