Toshiba B-852 owner manual Using the Printer Driver

Page 71

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.10 Installing the Printer Drivers

2.10.7 Using the Printer Driver

For how to use the Printer Driver, please refer to the Help for Windows Printer Drivers screen.

1)Open the Properties screen of the Printer Driver.

2)Clicking on the About tab causes the following screen to appear. Click on the [Help] button.

About tab

[Help] button

3)The Help for Windows Printer Drivers screen appears. This screen will provide how to use the printer driver.

E2-58

Image 71

Contents Series Vorsicht CE Compliance for EU onlySeries Waste Recycling information for users Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA1-1 E3-1E4-1 E5-1Unpacking Introduction FeaturesProduct Overview Accessories Front View Rear View DimensionsAppearance Interior Operation PanelOption Name Type Description OptionsManual threshold setting Printer SetupSetup Flow ProcedureInstallation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Power Cord Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder UnitLoading the Media Straight and true through the printerSpacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterEnvironment How to enter the System ModeSequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayedAfter selecting a character code, press the Pause key Character Zero SelectionCharacter Code Selection Use the Feed or Restart key to select a desired optionAfter selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length SelectionFlow Control Code Selection Stop Bit Length SelectionParity Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait SelectionFeed key Control Code SelectionAfter selecting the Feed key function, press the Pause key Feed Key Function SelectionAfter selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code SelectionAfter selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing SelectionAfter selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection After selecting a Plug & Play, press the Pause key Expansion I/O Interface Type SelectionPlug & Play Selection After selecting a Label End type, press the Pause key Maxi Code Specification SelectionLabel End/Ribbon End Selection After selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing methodRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed Basic Expansion ModeNot activated Activated Feed gap sensor Black mark sensor LAN Setting Time Setting Date SettingCont Real Time Clock Setting 3 Low Battery Check SettingRTC Data Renewal Timing Setting IP Address Setting TCP/IP Feed and Pause keys This parameter is to set a Gateway IP address Printer IP AddressThis parameter is to set an IP address Gateway IP AddressSocket Port Subnet MaskThis parameter is to set a Subnet Mask This parameter is to set a Dhcp client ID This parameter is to enable DhcpDhcp Dhcp Client IDAscii code and Hex. code correspondence table Dhcp Host NameThis parameter is to set a Dhcp host name General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using an optional Cutter Module Threshold Fine Adjustment Feed gap sensor Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine AdjustmentWhen setting +0.0 mm After selecting a fine adjustment value, press the Pause keyPosition and Print Tone Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Select the sensor to be adjusted by using the Feed keyLower Black Mark Sensor/Feed Gap Sensor Adjustment No media Upper Black Mark Sensor AdjustmentLower Black Mark Sensor Adjustment Feed Gap Sensor Adjustment„ When using the Feed Gap Sensor „ When using the Black Mark SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage Feed Gap Sensor Used to restart printing On Line ModeOperation Panel Used to stop printing temporarilyPress and hold the Restart key for 3 seconds or longer Operation ResetPrint Head/Platen/ Sensors MaintenanceCleaning Optional Cutter Module Covers and PanelsSolutions TroubleshootingError Messages Error Messages Problems/CausesRestart key Error Messages Problems/CauseMedia has run out Possible Problems Causes Possible ProblemsAttach the Cutter Cover properly Remove the jammed paper Clean the Cutter BladeLoad the ribbon properly Removing Jammed Media Model 852-TS22-QQ-R 852-TS22-QP-R Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media TypeDetection Area of the Reflective Sensor Detection Area of the Transmissive SensorFigure below shows the effective print area on the media Effective Print AreaMedia type Description RibbonRecommended Media and Ribbon Types Media type Vellum paper and label Care/Handling of the Media and RibbonRibbon type Description Combination of Media and RibbonAppendix 1 Messages and Leds Symbols in the messageDhcp Client is being initialised Command error has occurredAnalyzing the command 100BASE LAN is being initialisedFollowing message appears Parallel interface Centronics Appendix 2 InterfaceConnector LED status Link LED Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 StandardSerial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits JAN8, EAN8 MSI Interleaved 2NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digits CODE39 Full AsciiCustomer bar code of high priority QR code UPC-A+2 digitsUPC-A+5 digits Industrial 2 Data MatrixAppendix 4 Glossaries USB Universal Serial Bus See Black mark sensorMedia and ribbon See Feed gap sensor3-1, A1-1 IndexIndex EO1-33055D

Related manuals

Manual 2 pages 62.15 Kb