Toshiba B-852 owner manual E2-47

Page 60

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.10 Installing the Printer Drivers

(3)Select “Search for the best driver for your device. (Recommended)”.

Mark the “Specify a location” checkbox, then click on the [Browse] button. Specify “\driver” folder, then click on the [Next] button.

(4) Check to see that the “USB Printing Support” driver is detected, then click on the [Next] button.

E2-47

Image 60

Contents Series CE Compliance for EU only VorsichtSeries Waste Recycling information for users Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents E3-1 E4-1E5-1 EA1-1Introduction Features Product OverviewUnpacking Accessories Dimensions AppearanceFront View Rear View Operation Panel InteriorOptions Option Name Type DescriptionPrinter Setup Setup FlowProcedure Manual threshold settingInstallation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Power Cord Installing the Media onto the Supply Holder Unit Loading the MediaStraight and true through the printer Disassembling the Supply Holder UnitSpacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterHow to enter the System Mode EnvironmentParameter Setting While 2PARAMETER SET is displayed on the LCD MessageTime the Pause key is pressed, the sub menus are displayed SequentiallyCharacter Zero Selection Character Code SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause keyBaud Rate Selection After selecting a baud rate, press the Pause keyData Length Selection After selecting a data length, press the Pause keyStop Bit Length Selection Parity SelectionFlow Control Code Selection LCD Language Selection After selecting a language, press the Pause keyAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyControl Code Selection Feed keyFeed Key Function Selection After selecting the Feed key function, press the Pause keyKanji Code Selection After selecting a Kanji code, press the Pause keyEuro Code Selection After selecting a Euro code, press the Pause keyAuto Print Head Check Selection After selecting auto print head check, press the Pause keyCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyWeb Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Expansion I/O Interface Type Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Maxi Code Specification Selection Label End/Ribbon End SelectionAfter selecting a Label End type, press the Pause key Dump Mode Setting After selecting the receive buffer, press the Pause keyUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyData in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length Basic Expansion Mode When the Pause key is pressed, Basic program is executedNot activated Activated Feed gap sensor Black mark sensor LAN Setting Date Setting Time SettingReal Time Clock Setting 3 Low Battery Check Setting RTC Data Renewal Timing SettingCont IP Address Setting TCP/IP Feed and Pause keys Printer IP Address This parameter is to set an IP addressGateway IP Address This parameter is to set a Gateway IP addressSubnet Mask This parameter is to set a Subnet MaskSocket Port This parameter is to enable Dhcp DhcpDhcp Client ID This parameter is to set a Dhcp client IDDhcp Host Name This parameter is to set a Dhcp host nameAscii code and Hex. code correspondence table Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using an optional Cutter Module Position and Print Tone Fine Adjustment Feed Amount Fine AdjustmentCoordinate Fine Adjustment Threshold Fine Adjustment Feed gap sensorAfter selecting a fine adjustment value, press the Pause key When setting +0.0 mmPosition and Print Tone Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Jam errorsSelect the sensor to be adjusted by using the Feed key Manually setUpper Black Mark Sensor Adjustment Lower Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Lower Black Mark Sensor/Feed Gap Sensor Adjustment No media„ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds Feed Gap Sensor On Line Mode Operation PanelUsed to stop printing temporarily Used to restart printingOperation Reset Press and hold the Restart key for 3 seconds or longerMaintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter ModuleTroubleshooting Error MessagesError Messages Problems/Causes SolutionsError Messages Problems/Cause Media has run outRestart key Possible Problems Possible Problems CausesClean the Cutter Blade Load the ribbon properlyAttach the Cutter Cover properly Remove the jammed paper Removing Jammed Media Printer Specifications This section describes the printer specificationsModel 852-TS22-QQ-R 852-TS22-QP-R Mail 4STATE Customer CODE, RSS14 Supply Specifications MediaMedia Type LabelDetection Area of the Transmissive Sensor Detection Area of the Reflective SensorEffective Print Area Figure below shows the effective print area on the mediaRibbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of the Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Media type Vellum paper and labelSymbols in the message Appendix 1 Messages and LedsCommand error has occurred Analyzing the command100BASE LAN is being initialised Dhcp Client is being initialisedFollowing message appears Appendix 2 Interface Parallel interface CentronicsConnector Number of ports Power source Self power Connector Type B Number of ports Connector RJ-45Standard LED status Link LEDSerial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples JAN8, EAN8 MSI Interleaved 2 NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digitsCODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digitsIndustrial 2 Data Matrix Customer bar code of high priority QR codeAppendix 4 Glossaries See Black mark sensor Media and ribbonSee Feed gap sensor USB Universal Serial BusIndex 3-1, A1-1Index EO1-33055D

Related manuals

Manual 2 pages 62.15 Kb