Toshiba B-852 owner manual When using an optional Cutter Module

Page 73

2. PRINTER SETUP

ENGLISH VERSION EO1-33055

2.11 Print Test

2.11 Print Test (Cont.)

When using an optional Cutter Module

It is necessary to set the issue mode, cut position, etc. for the Printer Driver or TPCL (TEC Printer Command Language) in accordance with your printing condition.

For details of the TPCL, refer to the B-852 Series External Equipment Interface Specification stored in the CD-ROM.

Regarding how to use the Printer Driver, refer to the Help for the Windows Printer Drivers screen.

To gain maximum performance and life from the Cutter Module, periodic cleaning is required.

Before starting a cleaning, be sure to TURN OFF the printer to avoid risk of injury.

For details of cleaning, refer to Section 4.1.3 Optional Cutter Module.

E2-60

Image 73

Contents Series Vorsicht CE Compliance for EU onlySeries Waste Recycling information for users Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents E4-1 E3-1E5-1 EA1-1Product Overview Introduction FeaturesUnpacking Accessories Appearance DimensionsFront View Rear View Interior Operation PanelOption Name Type Description OptionsSetup Flow Printer SetupProcedure Manual threshold settingInstallation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Power Cord Loading the Media Installing the Media onto the Supply Holder UnitStraight and true through the printer Disassembling the Supply Holder UnitSpacer Supply Holder Loading Media into the Printer Print Head Element Head Block Release Lever Down Setting the Feed Gap Sensor Setting Sensor PositionsSetting the Black Mark Sensor Loading the Ribbon Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterEnvironment How to enter the System ModeWhile 2PARAMETER SET is displayed on the LCD Message Parameter SettingTime the Pause key is pressed, the sub menus are displayed SequentiallyCharacter Code Selection Character Zero SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause keyAfter selecting a baud rate, press the Pause key Baud Rate SelectionData Length Selection After selecting a data length, press the Pause keyParity Selection Stop Bit Length SelectionFlow Control Code Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyFeed key Control Code SelectionAfter selecting the Feed key function, press the Pause key Feed Key Function SelectionAfter selecting a Kanji code, press the Pause key Kanji Code SelectionEuro Code Selection After selecting a Euro code, press the Pause keyAfter selecting auto print head check, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyInput Prime Selection Web Printer Function SelectionAfter selecting the Input Prime, press the Pause key Plug & Play Selection Expansion I/O Interface Type SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon End Selection Maxi Code Specification SelectionAfter selecting a Label End type, press the Pause key After selecting the receive buffer, press the Pause key Dump Mode SettingUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyReceive Buffer Size Data in the receive buffer is printed as followsRequired Label Length When the Pause key is pressed, Basic program is executed Basic Expansion ModeNot activated Activated Feed gap sensor Black mark sensor LAN Setting Time Setting Date SettingRTC Data Renewal Timing Setting Real Time Clock Setting 3 Low Battery Check SettingCont IP Address Setting TCP/IP Feed and Pause keys This parameter is to set an IP address Printer IP AddressGateway IP Address This parameter is to set a Gateway IP addressThis parameter is to set a Subnet Mask Subnet MaskSocket Port Dhcp This parameter is to enable DhcpDhcp Client ID This parameter is to set a Dhcp client IDThis parameter is to set a Dhcp host name Dhcp Host NameAscii code and Hex. code correspondence table Introduction Installing the Printer DriversGeneral Description Parallel Interface Installing the Printer DriverWindows 98/Me E2-43 Windows 2000/XP E2-45 USB Interface E2-47 E2-48 E2-49 Finish button E2-51 E2-52 E2-53 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using an optional Cutter Module Feed Amount Fine Adjustment Position and Print Tone Fine AdjustmentCoordinate Fine Adjustment Threshold Fine Adjustment Feed gap sensorWhen setting +0.0 mm After selecting a fine adjustment value, press the Pause keyPosition and Print Tone Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPrint Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Jam errors Threshold SettingSelect the sensor to be adjusted by using the Feed key Manually setLower Black Mark Sensor Adjustment Upper Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Lower Black Mark Sensor/Feed Gap Sensor Adjustment No media„ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingPress and hold the Restart or Feed key for about 3 seconds Feed Gap Sensor Operation Panel On Line ModeUsed to stop printing temporarily Used to restart printingPress and hold the Restart key for 3 seconds or longer Operation ResetCleaning MaintenancePrint Head/Platen/ Sensors Optional Cutter Module Covers and PanelsError Messages TroubleshootingError Messages Problems/Causes SolutionsMedia has run out Error Messages Problems/CauseRestart key Possible Problems Causes Possible ProblemsLoad the ribbon properly Clean the Cutter BladeAttach the Cutter Cover properly Remove the jammed paper Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel 852-TS22-QQ-R 852-TS22-QP-R Mail 4STATE Customer CODE, RSS14 Media Supply SpecificationsMedia Type LabelDetection Area of the Reflective Sensor Detection Area of the Transmissive SensorFigure below shows the effective print area on the media Effective Print AreaRecommended Media and Ribbon Types RibbonMedia type Description Ribbon type Description Care/Handling of the Media and RibbonCombination of Media and Ribbon Media type Vellum paper and labelAppendix 1 Messages and Leds Symbols in the messageAnalyzing the command Command error has occurred100BASE LAN is being initialised Dhcp Client is being initialisedFollowing message appears Parallel interface Centronics Appendix 2 InterfaceConnector Number of ports Connector RJ-45 Number of ports Power source Self power Connector Type BStandard LED status Link LEDSerial interface Option B-SA704-RS-QM-R Wireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Print Samples NW7 JAN13, EAN13 UPC-E EAN13+2 digits EAN13+5 digits JAN8, EAN8 MSI Interleaved 2CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+5 digits UPC-A+2 digitsIndustrial 2 Data Matrix Customer bar code of high priority QR codeAppendix 4 Glossaries Media and ribbon See Black mark sensorSee Feed gap sensor USB Universal Serial Bus3-1, A1-1 IndexIndex EO1-33055D

Related manuals

Manual 2 pages 62.15 Kb