Toshiba IK-TF5C instruction manual Changing each setting in 1P SR mode, Mode = E.TRG E.TRG = 1P SR

Page 15

(1. 3. 2) Changing each setting in 1P SR mode

	Move up down	Set by pushing
	By pushing
		DATA UP, DOWN
	MENU UP, DOWN

-- SHUTTER --
MODE	E.TRG
E.TRG	1P SR
TRG.P
EXP.	16ms
PART	OFF

<MODE = E.TRG E.TRG = 1P SR>

•Sutter mode MANU, SS, E.TRG

•E.TRG mode

1P SNR, 1P SR, PW SNR, PW SR, RR

•Input trigger pulse setting at 1P SNR and 1P SR

Input trigger pulse : positive polarity

Input trigger pulse : negative polarity

•Exposure time setting at 1P SNR and 1P SR

0.01ms0.02 ms0.4 ms1 ms16 ms

0.01 ms	0.02 ms	0.1 ms	1 ms
step	step	step	step

•Partial scanning switch OFF/120fps/180fps/E.120fps/E.180fps

(a) Changing the polarity of inputting trigger pulse setting

1Set the "→" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.

2Select either , by pushing [DATA UP], [DATA DOWN] buttons.

(b) Changing 1P SR exposure time setting

1Set the "→" to EXP. by pushing [MENU UP], [MENU DOWN] buttons.

2Set the exposure time by pushing [DATA UP], [DATA DOWN] buttons.

Note:

The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras become: fixed pattern noise, white pixels, etc.

(c) Changing the partial scanning setting

1Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.

2Select either OFF/120fps/180fps/E.120fps/E.180fps by pushing [DATA UP], [DATA DOWN] buttons.

15

Image 15

Contents Following information is only for EU-member states For Customer UseSafety Precautions Disclaimer Avoid setting in humid, smoky, vaporized or dusty placesTable of Contents Components Available selections Items Controlled by Using on Screen DisplayNames and Functions Connector Pin Assignments ConnectionStandard Connection Result displayed Meaning OperationWhite Balance Automatic White Balance Manual White Balance OutlineOFF Shutter speed mode is E.TRG modeGain Shading CorrectionUsing the Menus Mode Setting by on Screen DisplayShutter Electronic shutter Changing each setting in Manu modePartial scanning setting MenusChanging each setting in SS synchro. scan mode Mode = SSChanging the shutter speed setting Changing 1P SNR exposure time setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing the polarity of inputting trigger pulse settingChanging each setting in 1P SR mode Mode = E.TRG E.TRG = 1P SRChanging 1P SR exposure time setting Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeChanging the gain in Manu mode Changing each setting in RR modeMode = E.TRG E.TRG = RR Changing each setting in GainWHT BAL White balance Changing R pedestal Changing the shading correction modeChanging the manual shading correction setting Changing master pedestalData UP, Down Menu UP, Down Adjusting horizontal phaseSync OptionExternal Sync Setting to factory setting statusExternal sync signal polarity Shutter mode HD input VD inputHorizontal phase adjustment Setting by the frameUsing the unit with external sync signal Setting by 1HFval Lval Dval 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing EXT Trig External triggerInternal VD*3 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPW SNR Pulse width trigger SYNC-NON Reset About 7 ∝s 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETRR Reset restart Input Timing Chart ExampleLong Term Exposure Partial Scanning on When Partial Scanning Mode is onPartial Read Partial Scanning OFF All pixels scanningInput Output Signal Specificatoins CCD Output Waveform Timing Chart Horizontal Output Waveform Timing ChartVertical Output Waveform Timing Chart RGB, 3CCD SpecificationsExternal Appearance Diagram Before Making a Service CallSymptom Items to be checked Limited One 1 Year Warranty of Labor and Parts Step-by-step Procedures How to Obtain Warranty ServiceImaging Systems Division