Toshiba IK-TF5C instruction manual Changing each setting in SS synchro. scan mode, Mode = SS

Page 13

(1. 2) Changing each setting in SS (synchro. scan) mode

	Move up down	Set by pushing
	By pushing
		DATA UP, DOWN
	MENU UP, DOWN

-- SHUTTER --
MODE	SS
SS	OFF
PART	OFF

<MODE = SS>

(a) Changing the shutter speed setting

•Sutter mode MANU, SS, E.TRG

•Synchro. scanning setting

OFF : 1H/525H↔524H/525H↔OFF↔2FRM↔512FRM

120fps, E.120fps : 1H/262H↔261H/262H↔OFF↔2FRM↔512FRM

180fps, E.180fps : 1H/175H↔174H/175H↔OFF↔2FRM↔512FRM

•Partial scanning switch OFF/120fps/180fps/E.120fps/E.180fps

1Set the "→" to SS by pushing [MENU UP], [MENU DOWN] buttons.

2Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.

(b) Partial scanning setting

1Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.

2Select either OFF/120fps/180fps/E.120fps/E.180fps by pushing [DATA UP], [DATA DOWN] buttons.

Note:

The slow shutter speed may increase the fixed pattern noise and/or the white pixels. This is a charac- teristic of CCD, and is not a symptom of malfunction.

Image 13

Contents Following information is only for EU-member states For Customer UseSafety Precautions Disclaimer Avoid setting in humid, smoky, vaporized or dusty placesTable of Contents Components Available selections Items Controlled by Using on Screen DisplayNames and Functions Connection Connector Pin AssignmentsStandard Connection White Balance OperationAutomatic White Balance Manual White Balance Outline Result displayed MeaningGain Shutter speed mode is E.TRG modeShading Correction OFFUsing the Menus Mode Setting by on Screen DisplayPartial scanning setting Changing each setting in Manu modeMenus Shutter Electronic shutterMode = SS Changing each setting in SS synchro. scan modeChanging the shutter speed setting Changing each setting in 1P SNR mode Changing each setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingMode = E.TRG E.TRG = 1P SR Changing each setting in 1P SR modeChanging 1P SR exposure time setting Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeMode = E.TRG E.TRG = RR Changing each setting in RR modeChanging each setting in Gain Changing the gain in Manu modeWHT BAL White balance Changing the manual shading correction setting Changing the shading correction modeChanging master pedestal Changing R pedestalSync Adjusting horizontal phaseOption Data UP, Down Menu UP, DownExternal sync signal polarity Setting to factory setting statusShutter mode HD input VD input External SyncUsing the unit with external sync signal Setting by the frameSetting by 1H Horizontal phase adjustment1 Pulse Trigger SYNC-NON Reset Picture Output Timing 1P SNR 1 Pulse Trigger Sync Non ResetEXT Trig External trigger Fval Lval DvalInternal VD*3 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPW SNR Pulse width trigger SYNC-NON Reset About 7 ∝s 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETInput Timing Chart Example RR Reset restartLong Term Exposure Partial Read When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning onInput Output Signal Specificatoins Horizontal Output Waveform Timing Chart CCD Output Waveform Timing ChartVertical Output Waveform Timing Chart RGB, 3CCD SpecificationsBefore Making a Service Call External Appearance DiagramSymptom Items to be checked Step-by-step Procedures How to Obtain Warranty Service Limited One 1 Year Warranty of Labor and PartsImaging Systems Division