Toshiba IK-TF5C instruction manual Changing each setting in PW SR mode, Mode = E.TRG E.TRG = PW SR

Page 17

(1. 3. 4) Changing each setting in PW SR mode

	Move up down	Set by pushing
	By pushing
		DATA UP, DOWN
	MENU UP, DOWN

-- SHUTTER --
MODE	E.TRG
E.TRG	PW SR
TRG.P
PART	OFF

<MODE = E.TRG E.TRG = PW SR>

•Sutter mode MANU, SS, E.TRG

•E.TRG mode

1P SNR, 1P SR, PW SNR, PW SR, RR

•Input trigger pulse setting at PW SNR and PW SR

Input trigger pulse : positive polarity Input trigger pulse : negative polarity

•Partial scanning switch OFF/120fps/180fps/E.120fps/E.180fps

(a) Changing the polarity of inputting trigger pulse setting

1Set the "→" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.

2Select either , by pushing [DATA UP], [DATA DOWN] buttons.

Note:

The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras become: fixed pattern noise, white pixels, etc.

Image 17

Contents Following information is only for EU-member states For Customer UseSafety Precautions Disclaimer Avoid setting in humid, smoky, vaporized or dusty placesTable of Contents Components Available selections Items Controlled by Using on Screen DisplayNames and Functions Standard Connection Connector Pin AssignmentsConnection White Balance OperationAutomatic White Balance Manual White Balance Outline Result displayed MeaningGain Shutter speed mode is E.TRG modeShading Correction OFFUsing the Menus Mode Setting by on Screen DisplayPartial scanning setting Changing each setting in Manu modeMenus Shutter Electronic shutterChanging the shutter speed setting Changing each setting in SS synchro. scan modeMode = SS Changing each setting in 1P SNR mode Changing each setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingChanging 1P SR exposure time setting Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeMode = E.TRG E.TRG = RR Changing each setting in RR modeChanging each setting in Gain Changing the gain in Manu modeWHT BAL White balance Changing the manual shading correction setting Changing the shading correction modeChanging master pedestal Changing R pedestalSync Adjusting horizontal phaseOption Data UP, Down Menu UP, DownExternal sync signal polarity Setting to factory setting statusShutter mode HD input VD input External SyncUsing the unit with external sync signal Setting by the frameSetting by 1H Horizontal phase adjustment1 Pulse Trigger SYNC-NON Reset Picture Output Timing 1P SNR 1 Pulse Trigger Sync Non ResetEXT Trig External trigger Fval Lval DvalInternal VD*3 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPW SNR Pulse width trigger SYNC-NON Reset About 7 ∝s 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETLong Term Exposure RR Reset restartInput Timing Chart Example Partial Read When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning onInput Output Signal Specificatoins Vertical Output Waveform Timing Chart CCD Output Waveform Timing ChartHorizontal Output Waveform Timing Chart RGB, 3CCD SpecificationsSymptom Items to be checked External Appearance DiagramBefore Making a Service Call Imaging Systems Division Limited One 1 Year Warranty of Labor and PartsStep-by-step Procedures How to Obtain Warranty Service