Toshiba IK-TF5C instruction manual External Appearance Diagram, Before Making a Service Call

Page 35

11. EXTERNAL APPEARANCE DIAGRAM

[1.73]

[0.20]

[1.02]

2-M3 Depth 3	78
	[3.07]

Unit : mm [inch]

6.312

[0.25] [0.47]

			(AWB)
		DISP
		DC IN 12V	MENU DATA	[0.32]
34	[1.34]	DC IN 12V	8.2
34	[1.34]	PAGE	8.2

22	[0.87]
	5	56
	[0.20]	[2.20]

4.8 [0.19]

4-M3 Depth 3

2-M2

26	[1.02]	25	[0.98]
	25		25
	[0.98]		[0.98]

19.2

[0.76]

[1.02]

4-M2 Depth 3

∗ inch=mm/25.4

12. BEFORE MAKING A SERVICE CALL

Symptom	Items to be checked
No image	• Is the power supplied correctly?
	• Is the lens iris adjusted correctly?
	• Are the cables connected correctly?
	• Is the shutter mode set correctly?
	• Is the image process equipment set correctly?
Poor color	• Is the monitor adjusted correctly?
	• Is the white balance of the camera adjusted correctly?
	• Is the illumination dark?

Image 35

Contents Following information is only for EU-member states For Customer UseSafety Precautions Disclaimer Avoid setting in humid, smoky, vaporized or dusty placesTable of Contents Components Available selections Items Controlled by Using on Screen DisplayNames and Functions Standard Connection Connector Pin AssignmentsConnection Result displayed Meaning OperationWhite Balance Automatic White Balance Manual White Balance OutlineOFF Shutter speed mode is E.TRG modeGain Shading CorrectionUsing the Menus Mode Setting by on Screen DisplayShutter Electronic shutter Changing each setting in Manu modePartial scanning setting MenusChanging the shutter speed setting Changing each setting in SS synchro. scan modeMode = SS Changing 1P SNR exposure time setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing the polarity of inputting trigger pulse settingChanging 1P SR exposure time setting Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeChanging the gain in Manu mode Changing each setting in RR modeMode = E.TRG E.TRG = RR Changing each setting in GainWHT BAL White balance Changing R pedestal Changing the shading correction modeChanging the manual shading correction setting Changing master pedestalData UP, Down Menu UP, Down Adjusting horizontal phaseSync OptionExternal Sync Setting to factory setting statusExternal sync signal polarity Shutter mode HD input VD inputHorizontal phase adjustment Setting by the frameUsing the unit with external sync signal Setting by 1HFval Lval Dval 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing EXT Trig External triggerInternal VD*3 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPW SNR Pulse width trigger SYNC-NON Reset About 7 ∝s 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETLong Term Exposure RR Reset restartInput Timing Chart Example Partial Scanning on When Partial Scanning Mode is onPartial Read Partial Scanning OFF All pixels scanningInput Output Signal Specificatoins Vertical Output Waveform Timing Chart CCD Output Waveform Timing ChartHorizontal Output Waveform Timing Chart RGB, 3CCD SpecificationsSymptom Items to be checked External Appearance DiagramBefore Making a Service Call Imaging Systems Division Limited One 1 Year Warranty of Labor and PartsStep-by-step Procedures How to Obtain Warranty Service