Liebert SERIES 300 UPS manual Abnormal Conditions During Start-Up

3.6.2Abnormal Conditions During Start-Up

,IýWKHýV\VWHPýGHWHFWVýDQýDEQRUPDOýFRQGLWLRQýGXULQJýVWDUWðXSã

ìï $Qý$GYLVRU\ý'LVSOD\ý/('ýPD\ýLOOXPLQDWHñýSURPSWLQJýPRYHPHQWýRIýWKHý5RWDU\ý6ZLWFKïý5HDGý WKHýVFUHHQýPHVVDJHýEHIRUHýWXUQLQJýWKHý5RWDU\ý6ZLWFKï

ëï 7KHýVFUHHQýGLVSOD\VýDQýDEQRUPDOýFRQGLWLRQýPHVVDJHïý6HHý7DEOH æýIRUýDQýH[SODQDWLRQýRIý GLVSOD\HGýPHVVDJHVýDQGýLPSOHPHQWýWKHýFRUUHVSRQGLQJýFRUUHFWLYHýDFWLRQï

êï 5HSHDWýVWDUWðXSýVHTXHQFHýLIýDEQRUPDOýFRQGLWLRQýFDQýEHýFOHDUHGïý&DOOý/LHEHUWý6HUYLFHýDQGý 6XSSRUWýLIý\RXýUHTXLUHýDVVLVWDQFHï

'XULQJýVWDUWðXSñýV\VWHPýFRPSRQHQWVýDUHýWHVWHGýDQGýDQ\ýDEQRUPDOýFRQGLWLRQVýDUHýGLVSOD\HGýLQýDQý $ODUPý0HVVDJHïý:KHQýDQýDEQRUPDOýFRQGLWLRQýRFFXUVýGXULQJýVWDUWðXSñýWKHýFULWLFDOýORDGýFRQWLQXHVýWRý UHFHLYHýSRZHUýWKURXJKýWKHý0DLQWHQDQFHý%\SDVVý/LQHïý,IýWKHýGHIDXOWýVFUHHQýLQVWUXFWVý\RXýWRý&KHFNý 0HVVDJHVñýSUHVVýWKHý'RZQýSDGýWRýVHHýWKHýDFWLYHý$ODUPý0HVVDJHVï

7DEOH æýVKRZVý$ODUPý0HVVDJHVý\RXýPD\ýVHHýGXULQJýVWDUWðXSñýDORQJýZLWKýRSHUDWRUýFRUUHFWLYHý DFWLRQïý$ODUPý0HVVDJHVý\RXýPD\ýVHHýGXULQJýQRUPDOýRSHUDWLRQýDUHýLQýêïìì ðý$ODUPý0HVVDJHVý õ7DEOH åôïý&RQWDFWý/LHEHUWý&XVWRPHUý6HUYLFHýDQGý6XSSRUWýDWýìðåííðèéêðëêæåýLIý\RXýUHTXLUHýDVVLVð WDQFHïý

Table 7 Alarm Messages During Start-Up

Alarm	Meaning and
Message	Corrective Action in Brackets [ ]
START-UP SEQUENCE ABORTED	Check Messages.
Input phase rotation incorrect	The power conductors are not wired to the UPS input in the desired
	sequence.
	[Disconnect power from the UPS input and correct the wiring. A Liebert
	Customer Service and Support representative must be present during
	initial start-up of your UPS system.]
Incorrect input frequency	The frequency of the input power is outside the specified acceptable
	range.
	[Check your utility source.]
Rotary switch is in the wrong position	Power has been applied to the UPS with the Rotary Switch in the wrong
	position. This message is displayed when the input power is removed, the
	battery is discharged, and the UPS system has completely shut down.
	This message indicates the Rotary Switch is still in Position 4 when input
	power is restored.
	[Turn the Rotary Switch to Position 1 and perform a UPS start-up
	procedure.]
Rotary switch improperly operated	The Rotary Switch has been operated improperly. This means the switch
	has been operated either too fast or in the wrong direction.
	[Turn the Rotary Switch to Position 1 and perform a UPS start-up
	procedure.]
Battery Failed Test	The Start-up test routine has detected a failure in the battery.
	[Contact Liebert Customer Service and Support at 1-800-543-2378.]
Static Switch Failure	The Start-up test routine has detected a failure in the Static Transfer
	Switch.
	[Contact Liebert Customer Service and Support at 1-800-543-2378.]

Operation 51