D-Link DWA-140 manual Computer to Router Connection

Page 19

Computer to Router Connection

You can connect the Router directly to a 10/100BASE-TX Ethernet adapter card (NIC) installed on a PC using the Ethernet cable provided as shown in this diagram.

Power On Router

To power on the Router:

1.Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Router and plug the adapter into a suitable nearby power source.

2.You should see the Power LED indicator light up and remain lit. The Status LED should light solid green and begin to blink after a few seconds.

3.If you have the Router connected to your network you can look at the Ethernet Link/Act LED and WLAN indicators to make sure they have valid connections. The Router will attempt to establish the ADSL connection, if the ADSL line is connected and the connection is properly configured this should light up after several seconds.

Factory Reset Button

The Router may be reset to the original factory default settings by depressing the reset button for a few seconds while the device is powered on. Use a ballpoint or paperclip to push down the reset button. Remember that this will wipe out any settings stored in flash memory including IP settings. The factory default IP address of the Router is 192.168.1.1 and the subnet mask is 255.255.255.0.

11

Image 19
Contents DSL-G604T Warnung Table of Contents Advanced Router Management About This User’s Guide Installation RequirementsBefore You Start About Clip Connections RFC 802.11b Wireless LAN ConfigurationEthernet Port NIC Adapter Additional SoftwareInformation you will need from your Adsl service provider LAN Subnet Mask for the DSL-G604T Packing ListIntroduction What is ADSL?Router Description and Operation Router Features Standards Compatibility and Compliance Front Panel Display Packing ListRear Panel Connections Radio Transmission Introduction to 802.11b Wireless802.11g Wireless Wireless LAN BasicsRange Adsl TechnologyLocation Hardware InstallationFactory Reset Button Power on RouterConnect Router to Ethernet Hub or Switch to Router ConnectionNetwork Connections Connect Adsl LineComputer to Router Connection Configuring IP Settings on Your Computer Basic Router ConfigurationWAN Configuration Summary Configure Windows XP for Dhcp Windows Configure Windows ME for Dhcp Configure Windows 2000 for DhcpWindows ME Windows 95 and Windows Configure Windows NT 4.0 for Dhcp Configure Windows 95 and Windows 98 for DhcpWindows NT 4.0 Workstations Login to Home Access the Configuration ManagerHome Status Information window Configure the RouterOpening Setup window Setup MenuWireless configuration window Wireless SettingsWEP configuration window Wireless Security802.1X 1X configuration windowPSK String WPA Wi-Fi Protected AccessModem Setup Configure Connection 1 for PPPoAPPPoA Connection 1 Setup menu Change the Connection Type Configure Connection 1 for PPPoEPage 11. Setup Configure Connection 1 for Bridge Configure Connection 1 for Bridge12. Setup Configure Connection 1 for Static IP for the WAN Configure Connection 1 for Static IP for WANPage Configure Connection 1 for Dhcp for WAN 14. Setup Configure Connection 1 for Clip IPoA Configure Connection 1 for ClipNew Connection Example 1 Create a New PPPoE Connection Create a New ConnectionNew Connection Example 2 Create a New Bridge Connection 16. Set up a New Connection ConnectionLease Time Dhcp Configuration for LANDhcp Parameter Description Start IP End IP18. Configure Dhcp Relay Service Enable Dhcp RelayManagement IP 19. Configure Management IP20. Router Tools Menus Save Configuration Changes22. Changes permanently saved message Advanced Router Management Advanced setup main menuAdvanced UPnP window UPnPLAN Clients LAN Clients SetupAdvanced Port Forwarding window Port ForwardingServers Category Available Rules GamesAudio/Video ApplicationsSet up Custom Port Forwarding Rules Page Access Control menu Access ControlVPN Advanced Security Enable/Disable NAT and FirewallDMZ IP Address Bridge Filters Setup Remote Management10. Multicast pass-through menu Multicast Pass-through11. Static Routing menu Static Routing12. Dynamic Routing RIP menu Dynamic RoutingMultiple Virtual Connections Wireless ManagementPage 13. Tools and utility menu links Tools and Utility Menus14. User Management menu User Management15. Tools System Commands menu System Commands16. Remote Log menu Remote Log17. Tools Update Gateway window Update Gateway18. Tools Ping Test window Ping Test19. Tools Modem Test window Modem Test20. Status display links Status Menus21. Network Statistics window Network Statistics22. Connection Status window Connection Status23. Dhcp Clients window Dhcp Clients24. Modem Status window Modem Status25. Product Information window Product Information26. System Log window System Log27. Opening Help window Help MenuTechnical Specifications CE Class B, FCC Class B Part Physical and EnvironmentalManual IP Address Assignment IP Address SetupUsing the Default IP Address Assigning Network IP AddressesIP Setup Example #2 Using DhcpChanging the IP Address of the Router IP Addresses IP ConceptsClass Beginning Address Ending Address Subnet MaskClass a 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0 IP Class Subnet MaskMicrofilters and Splitters Microfilter InstallationMicrofilters Line Splitter Line Splitter Installation