D-Link DWA-140 manual Remote Log menu

Page 68

Remote Log

Us the Remote Log menu to set up logging to servers or computers that are located outside the LAN or subnet of the Router.

Figure 4-16. Remote Log menu

Select the Log Level from the pull-down menu. The levels available are: Alert, Critical, Debug, Error, Info, Notice, Panic and Warning. Type in the IP address of a receiver for the log message in the Add an IP Address field and click on the Add button. Log message receivers that are added appear listed in the Select a logging destination pull-down menu. These may be used at any time for other types of log messages. To remove a log message receiver from the list, select it and click on the Remove button. Click the Apply button when you have configured the log message receivers. Remember to save the settings to non-volatile memory.

60

Image 68
Contents DSL-G604T Warnung Table of Contents Advanced Router Management Before You Start Installation RequirementsAbout This User’s Guide 802.11b Wireless LAN Configuration Ethernet Port NIC AdapterAdditional Software About Clip Connections RFCInformation you will need from your Adsl service provider Packing List LAN Subnet Mask for the DSL-G604TRouter Description and Operation What is ADSL?Introduction Router Features Standards Compatibility and Compliance Packing List Front Panel DisplayRear Panel Connections Introduction to 802.11b Wireless 802.11g WirelessWireless LAN Basics Radio TransmissionAdsl Technology RangeHardware Installation LocationPower on Router Factory Reset ButtonHub or Switch to Router Connection Network ConnectionsConnect Adsl Line Connect Router to EthernetComputer to Router Connection WAN Configuration Summary Basic Router ConfigurationConfiguring IP Settings on Your Computer Configure Windows XP for Dhcp Windows Windows ME Configure Windows 2000 for DhcpConfigure Windows ME for Dhcp Windows 95 and Windows Windows NT 4.0 Workstations Configure Windows 95 and Windows 98 for DhcpConfigure Windows NT 4.0 for Dhcp Access the Configuration Manager Login to HomeConfigure the Router Home Status Information windowSetup Menu Opening Setup windowWireless Settings Wireless configuration windowWireless Security WEP configuration window1X configuration window 802.1XWPA Wi-Fi Protected Access PSK StringConfigure Connection 1 for PPPoA Modem SetupPPPoA Connection 1 Setup menu Configure Connection 1 for PPPoE Change the Connection TypePage Configure Connection 1 for Bridge 11. Setup Configure Connection 1 for BridgeConfigure Connection 1 for Static IP for WAN 12. Setup Configure Connection 1 for Static IP for the WANPage Configure Connection 1 for Dhcp for WAN Configure Connection 1 for Clip 14. Setup Configure Connection 1 for Clip IPoACreate a New Connection New Connection Example 1 Create a New PPPoE Connection16. Set up a New Connection Connection New Connection Example 2 Create a New Bridge ConnectionDhcp Configuration for LAN Dhcp Parameter Description Start IPEnd IP Lease TimeEnable Dhcp Relay 18. Configure Dhcp Relay Service19. Configure Management IP Management IPSave Configuration Changes 20. Router Tools Menus22. Changes permanently saved message Advanced setup main menu Advanced Router ManagementUPnP Advanced UPnP windowLAN Clients Setup LAN ClientsPort Forwarding Advanced Port Forwarding windowCategory Available Rules Games Audio/VideoApplications ServersSet up Custom Port Forwarding Rules Page Access Control Access Control menuVPN DMZ IP Address Enable/Disable NAT and FirewallAdvanced Security Setup Remote Management Bridge FiltersMulticast Pass-through 10. Multicast pass-through menuStatic Routing 11. Static Routing menuDynamic Routing 12. Dynamic Routing RIP menuWireless Management Multiple Virtual ConnectionsPage Tools and Utility Menus 13. Tools and utility menu linksUser Management 14. User Management menuSystem Commands 15. Tools System Commands menuRemote Log 16. Remote Log menuUpdate Gateway 17. Tools Update Gateway windowPing Test 18. Tools Ping Test windowModem Test 19. Tools Modem Test windowStatus Menus 20. Status display linksNetwork Statistics 21. Network Statistics windowConnection Status 22. Connection Status windowDhcp Clients 23. Dhcp Clients windowModem Status 24. Modem Status windowProduct Information 25. Product Information windowSystem Log 26. System Log windowHelp Menu 27. Opening Help windowTechnical Specifications Physical and Environmental CE Class B, FCC Class B PartIP Address Setup Using the Default IP AddressAssigning Network IP Addresses Manual IP Address AssignmentChanging the IP Address of the Router Using DhcpIP Setup Example #2 IP Concepts IP AddressesSubnet Mask Class Beginning Address Ending AddressIP Class Subnet Mask Class a 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0Microfilters Microfilter InstallationMicrofilters and Splitters Line Splitter Installation Line Splitter