D-Link DWA-140 manual

Page 39

7.The Encapsulation values LLC (SNAP) and VC (MUX) are two different methods of encapsulating the PPP packet. Contact your ISP to make sure which encapsulation is being supported.

8.Based on the information provided by your ISP, enter the IP Address, Subnet Mask, Default Gateway (if provided), and Domain Name Services (DNS) values (if provided).

9.Select the desired Mode, Bridged or Routed.

10.Click the Apply button when you have entered all the information. The web browser will briefly go blank. You are now finished changing setting for the primary WAN connection known as Connection 1. It is now necessary to save the changes you just made and restart the Router.

11.To save the changes made to Connection 1, click the Tools tab and then click on the System Commands button. Click on the Save All button to store the configuration settings. Click on Back button to return to the System Commands menu.

12.Check the WAN connection status. Click the Status tab and then the Connection Status button. Look under WAN to view the State of Connection 1, it should read “ N/A”. If the WAN connection state does not appear to Connected after a few minutes, go back to the Connection 1 Setup menu, check the settings and make sure they are correct.

31

Image 39
Contents DSL-G604T Warnung Table of Contents Advanced Router Management Installation Requirements About This User’s GuideBefore You Start About Clip Connections RFC 802.11b Wireless LAN ConfigurationEthernet Port NIC Adapter Additional SoftwareInformation you will need from your Adsl service provider LAN Subnet Mask for the DSL-G604T Packing ListWhat is ADSL? IntroductionRouter Description and Operation Router Features Standards Compatibility and Compliance Front Panel Display Packing ListRear Panel Connections Radio Transmission Introduction to 802.11b Wireless802.11g Wireless Wireless LAN BasicsRange Adsl TechnologyLocation Hardware InstallationFactory Reset Button Power on RouterConnect Router to Ethernet Hub or Switch to Router ConnectionNetwork Connections Connect Adsl LineComputer to Router Connection Basic Router Configuration Configuring IP Settings on Your ComputerWAN Configuration Summary Configure Windows XP for Dhcp Windows Configure Windows 2000 for Dhcp Configure Windows ME for DhcpWindows ME Windows 95 and Windows Configure Windows 95 and Windows 98 for Dhcp Configure Windows NT 4.0 for DhcpWindows NT 4.0 Workstations Login to Home Access the Configuration ManagerHome Status Information window Configure the RouterOpening Setup window Setup MenuWireless configuration window Wireless SettingsWEP configuration window Wireless Security802.1X 1X configuration windowPSK String WPA Wi-Fi Protected AccessModem Setup Configure Connection 1 for PPPoAPPPoA Connection 1 Setup menu Change the Connection Type Configure Connection 1 for PPPoEPage 11. Setup Configure Connection 1 for Bridge Configure Connection 1 for Bridge12. Setup Configure Connection 1 for Static IP for the WAN Configure Connection 1 for Static IP for WANPage Configure Connection 1 for Dhcp for WAN 14. Setup Configure Connection 1 for Clip IPoA Configure Connection 1 for ClipNew Connection Example 1 Create a New PPPoE Connection Create a New ConnectionNew Connection Example 2 Create a New Bridge Connection 16. Set up a New Connection ConnectionLease Time Dhcp Configuration for LANDhcp Parameter Description Start IP End IP18. Configure Dhcp Relay Service Enable Dhcp RelayManagement IP 19. Configure Management IP20. Router Tools Menus Save Configuration Changes22. Changes permanently saved message Advanced Router Management Advanced setup main menuAdvanced UPnP window UPnPLAN Clients LAN Clients SetupAdvanced Port Forwarding window Port ForwardingServers Category Available Rules GamesAudio/Video ApplicationsSet up Custom Port Forwarding Rules Page Access Control menu Access ControlVPN Enable/Disable NAT and Firewall Advanced SecurityDMZ IP Address Bridge Filters Setup Remote Management10. Multicast pass-through menu Multicast Pass-through11. Static Routing menu Static Routing12. Dynamic Routing RIP menu Dynamic RoutingMultiple Virtual Connections Wireless ManagementPage 13. Tools and utility menu links Tools and Utility Menus14. User Management menu User Management15. Tools System Commands menu System Commands16. Remote Log menu Remote Log17. Tools Update Gateway window Update Gateway18. Tools Ping Test window Ping Test19. Tools Modem Test window Modem Test20. Status display links Status Menus21. Network Statistics window Network Statistics22. Connection Status window Connection Status23. Dhcp Clients window Dhcp Clients24. Modem Status window Modem Status25. Product Information window Product Information26. System Log window System Log27. Opening Help window Help MenuTechnical Specifications CE Class B, FCC Class B Part Physical and EnvironmentalManual IP Address Assignment IP Address SetupUsing the Default IP Address Assigning Network IP AddressesUsing Dhcp IP Setup Example #2Changing the IP Address of the Router IP Addresses IP ConceptsClass Beginning Address Ending Address Subnet MaskClass a 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0 IP Class Subnet MaskMicrofilter Installation Microfilters and SplittersMicrofilters Line Splitter Line Splitter Installation