D-Link DWA-140 manual Microfilters and Splitters, Microfilter Installation

Page 87

D

Microfilters and Splitters

Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regular telephone services. These devices are commonly referred to as microfilters or sometimes called (inaccurately) line splitters. They are easy to install and use standard telephone connectors and cable.

Some ADSL service providers will send a telecommunications technician to modify the telephone line, usually at the point where the telephone line enters the building. If a technician has divided or split your telephone line into two separate lines - one for regular telephone service and the other for ADSL – then you do not need to use any type of filter device. Follow the instructions given to you by your ADSL service provider about where and how you should connect the Modem to the ADSL line.

Microfilters

Unless you are instructed to use a “ line splitter” (see below), it will be necessary to install a microfilter (low pass filter) device for each telephone or telephone device (answering machines, Faxes etc.) that shares the line with the ADSL service. Microfilters are easy-to-install, in-line devices, which attach to the telephone cable between the telephone and wall jack. Microfilters that install behind the wall plate are also available. A typical in-line microfilter installation is shown in the diagram below.

Microfilter Installation

Important: Do not install the microfilter between the Modem and the telephone jack. Microfilters are only intended for use with regular telephones, Fax machines and other regular telephone devices.

79

Image 87
Contents DSL-G604T Warnung Table of Contents Advanced Router Management Installation Requirements About This User’s GuideBefore You Start About Clip Connections RFC 802.11b Wireless LAN ConfigurationEthernet Port NIC Adapter Additional SoftwareInformation you will need from your Adsl service provider LAN Subnet Mask for the DSL-G604T Packing ListWhat is ADSL? IntroductionRouter Description and Operation Router Features Standards Compatibility and Compliance Front Panel Display Packing ListRear Panel Connections Radio Transmission Introduction to 802.11b Wireless802.11g Wireless Wireless LAN BasicsRange Adsl TechnologyLocation Hardware InstallationFactory Reset Button Power on RouterConnect Router to Ethernet Hub or Switch to Router ConnectionNetwork Connections Connect Adsl LineComputer to Router Connection Basic Router Configuration Configuring IP Settings on Your ComputerWAN Configuration Summary Configure Windows XP for Dhcp Windows Configure Windows 2000 for Dhcp Configure Windows ME for DhcpWindows ME Windows 95 and Windows Configure Windows 95 and Windows 98 for Dhcp Configure Windows NT 4.0 for DhcpWindows NT 4.0 Workstations Login to Home Access the Configuration ManagerHome Status Information window Configure the RouterOpening Setup window Setup MenuWireless configuration window Wireless SettingsWEP configuration window Wireless Security802.1X 1X configuration windowPSK String WPA Wi-Fi Protected AccessModem Setup Configure Connection 1 for PPPoAPPPoA Connection 1 Setup menu Change the Connection Type Configure Connection 1 for PPPoEPage 11. Setup Configure Connection 1 for Bridge Configure Connection 1 for Bridge12. Setup Configure Connection 1 for Static IP for the WAN Configure Connection 1 for Static IP for WANPage Configure Connection 1 for Dhcp for WAN 14. Setup Configure Connection 1 for Clip IPoA Configure Connection 1 for ClipNew Connection Example 1 Create a New PPPoE Connection Create a New ConnectionNew Connection Example 2 Create a New Bridge Connection 16. Set up a New Connection ConnectionLease Time Dhcp Configuration for LANDhcp Parameter Description Start IP End IP18. Configure Dhcp Relay Service Enable Dhcp RelayManagement IP 19. Configure Management IP20. Router Tools Menus Save Configuration Changes22. Changes permanently saved message Advanced Router Management Advanced setup main menuAdvanced UPnP window UPnPLAN Clients LAN Clients SetupAdvanced Port Forwarding window Port ForwardingServers Category Available Rules GamesAudio/Video ApplicationsSet up Custom Port Forwarding Rules Page Access Control menu Access ControlVPN Enable/Disable NAT and Firewall Advanced SecurityDMZ IP Address Bridge Filters Setup Remote Management10. Multicast pass-through menu Multicast Pass-through11. Static Routing menu Static Routing12. Dynamic Routing RIP menu Dynamic RoutingMultiple Virtual Connections Wireless ManagementPage 13. Tools and utility menu links Tools and Utility Menus14. User Management menu User Management15. Tools System Commands menu System Commands16. Remote Log menu Remote Log17. Tools Update Gateway window Update Gateway18. Tools Ping Test window Ping Test19. Tools Modem Test window Modem Test20. Status display links Status Menus21. Network Statistics window Network Statistics22. Connection Status window Connection Status23. Dhcp Clients window Dhcp Clients24. Modem Status window Modem Status25. Product Information window Product Information26. System Log window System Log27. Opening Help window Help MenuTechnical Specifications CE Class B, FCC Class B Part Physical and EnvironmentalManual IP Address Assignment IP Address SetupUsing the Default IP Address Assigning Network IP AddressesUsing Dhcp IP Setup Example #2Changing the IP Address of the Router IP Addresses IP ConceptsClass Beginning Address Ending Address Subnet MaskClass a 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0 IP Class Subnet MaskMicrofilter Installation Microfilters and SplittersMicrofilters Line Splitter Line Splitter Installation