NETGEAR WNR834M manual Configuring LAN TCP/IP Setup Parameters

Page 66

NETGEAR RangeMax™ NEXT Wireless Router WNR834M Reference Manual

Configuring LAN TCP/IP Setup Parameters

The router is shipped preconfigured to use private IP addresses on the LAN side, and to act.as a DHCP server. The router’s default LAN IP configuration is:

LAN IP address—192.168.1.1

Subnet mask—255.255.255.0

These addresses are part of the IETF-designated private address range for use in private networks, and should be suitable for most applications. If your network has a requirement to use a different IP addressing scheme, you can make those changes in this menu.

The LAN IP parameters are:

IP Address

This is the LAN IP address of the router.

IP Subnet Mask

This is the LAN Subnet Mask of the router. Combined with the IP address, the IP Subnet Mask allows a device to know which other addresses are local to it, and which must be reached through a gateway or router.

RIP Direction

RIP (Router Information Protocol) allows a router to exchange routing information with other routers. The RIP Direction selection controls how the router sends and receives RIP packets. Both is the default.

When set to Both or Out Only, the router broadcasts its routing table periodically.

When set to Both or In Only, the router incorporates the RIP information that it receives.

When set to None, the router does not send any RIP packets and ignores any RIP packets received.

RIP Version

This controls the format and the broadcasting method of the RIP packets that the router sends. (It recognizes both formats when receiving.) By default, this is set for RIP-1.

RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you have an unusual network setup.

RIP-2 carries more information. RIP-2B uses subnet broadcasting.

Note: If you change the LAN IP address of the router while connected through the browser, you will be disconnected. You must then open a new connection to the

new IP address and log in again.

6-14

Advanced Configuration of the Router

v1.3, May 2006

Image 66
Contents NETGEAR, Inc Trademarks Statement of ConditionsEuropean Union Statement of Compliance Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/ImporterVoluntary Control Council for Interference Vcci Statement Customer SupportWorld Wide Web V1.3, May Contents Chapter Content Filtering Appendix a Technical Specifications V1.3, May Chapter About This Manual Audience, Scope, Conventions, and FormatsTypographical Conventions How to Use This Manual How to Print this ManualManual Scope Revision History Publication Revision HistoryV1.3, May Package Contents Chapter IntroductionFront of the Wireless Router Status LightBack of the Wireless Router Installing the WNR834M router How to Access the Wireless Router Again LaterRangeMax Next Wireless Router WNR834M Online Setup Manuals V1.3, May Maintenance and Support Chapter Wireless Configuration Observing Performance, Placement, and Range GuidelinesImplementing Appropriate Wireless Security V1.3, May Default Factory Settings If WPA-PSK or WPA2-PSK Authentication is UsedUnderstanding Wireless Settings Basic Wireless Security Options WEPV1.3, May How to Set Up and Test Basic Wireless Connectivity V1.3, May How to Configure WEP How to Configure WPA-PSK or WPA2-PSK Wireless Security How to Restrict Wireless Access by MAC Address Click the Turn Access Control On check boxV1.3, May V1.3, May Chapter Content Filtering Content Filtering OverviewBlocking Access to Internet Sites Blocking Access to Internet Services V1.3, May Scheduling When Blocking Will Be Enforced Configuring a User Defined ServiceBlocking Services by IP Address Range Viewing Logs of Web Access or Attempted Web Access Log entry descriptionsLog action buttons Configuring E-Mail Alert and Web Access Log Notifications V1.3, May Chapter Maintenance Viewing Wireless Router Status InformationWireless Router Status Fields This screen shows the following parametersWireless port of the router. The default is Netgear Region Connection Status Items Router Statistics ItemsConfiguration File Management Viewing a List of Attached DevicesBacking Up and Restoring the Configuration Erasing the ConfigurationUpgrading the Router Software V1.3, May Changing the Administrator Password V1.3, May Advanced Configuration of the Router Configuring Advanced Wireless SettingsPossibility, leave this checkbox unselected Wireless Card Access List Wireless Card Access Setup Configuring Port Triggering and Port Forwarding V1.3, May Click Add Service Configuring Port Forwarding to Local Servers Adding a Custom Service Click the Add Custom Service buttonEditing or Deleting a Port Forwarding Entry Local Web and FTP Server ExampleMultiple Computers for Internet Gaming Configuring the WAN Setup Options Connecting Automatically, as RequiredSetting Up a Default DMZ Server Disabling the SPI FirewallResponding to a Ping on the Internet WAN Port Using the LAN IP Setup Options Setting the MTU SizeConfiguring LAN TCP/IP Setup Parameters Using the Router as a Dhcp server Using Address ReservationUsing a Dynamic DNS Service Select the Use a Dynamic DNS Service check box Configuring Static Routes V1.3, May Enabling Remote Management Access Select the Turn Remote Management On check boxV1.3, May Using Universal Plug and Play UPnP V1.3, May V1.3, May Be sure to restart your network in this sequence Chapter TroubleshootingTroubleshooting Quick Tips Make sure the Ethernet cables are securely pluggedMake sure the network settings of the computer are correct Power Light Not OnBasic Functioning Lights Never Turn Off LAN or WAN Port Lights Not OnTroubleshooting the Web Configuration Interface Troubleshooting the ISP Connection Troubleshooting a TCP/IP Network Using a Ping Utility Testing the LAN Path to Your RouterTesting the Path from Your Computer to a Remote Device Restoring the Default Configuration and Password Problems with Date and Time V1.3, May Appendix a Technical Specifications Factory Default SettingsWireless General Specifications Regulatory ComplianceV1.3, May Appendix B Related Documents Document LinkV1.3, May