NETGEAR EX6100100NAS user manual Install the Extender as a Range Extender, Place the Extender

Page 10

AC750 WiFi Range Extender

Install the Extender as a Range Extender

The extender connects to your network’s WiFi signal and then rebroadcasts that signal to extend the WiFi signal coverage.

Place the Extender

NETGEAR recommends that you place the extender near the router during initial setup. Then you can move it farther away from the router as needed to increase the area that has a WiFi signal.

To place the extender:

1.Place your extender in the same room as your WiFi router.

2.Plug the extender into an electrical outlet.

The Power LED lights green. If the Power LED does not light, press the Power button.

3.Make sure that the switch on the extender is set to Extender.

Connect to an Existing WiFi Network

To extend the range of your WiFi network, you must connect the extender to your existing WiFi network. You can do this in one of two ways:

•Connect with WPS. For more information, see Connect with WPS on page 10.

•Connect with genie Smart Setup. For more information, see Connect with NETGEAR genie Smart Setup on page 11.

Connect with WPS

Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without typing the network name and password. The WPS button is a physical button on the router or access point. WPS does not support WEP network security. If you are using WEP security, see Connect with NETGEAR genie Smart Setup on page 11.

To connect with WPS:

1.Press the WPS button on the side panel of the extender.

The WPS LED blinks.

2.Within two minutes, press the WPS button on your router or access point.

The WPS LED on the extender lights solid green, the Router Link LED lights, and the extender is connected to your existing WiFi network.

Note: If the Router Link LED does not light, try again. If it still does not light, see Connect with NETGEAR genie Smart Setup on page 11.

Install Your Extender

10

Image 10

Contents AC750 WiFi Range Extender Compliance SupportTrademarks Contents FAQs and Troubleshooting Get to Know Your Extender Front Panel and Side Panel LEDs and Buttons WPS LEDUse as a WiFi Range Extender When to Use Your ExtenderHow the Extender Works Use as an Access Point Support for the 802.11ac Networking StandardInstall Your Extender Place the Extender Install the Extender as a Range ExtenderConnect to an Existing WiFi Network  To place the extenderExisting WiFi network name. MyNetworkName  To connect with the browser-based Smart SetupInstall Your Extender Install Your Extender Extender Performance Find the Best LocationConnect a Computer or Device to the Ethernet Port  To connect a computer to the extender Ethernet port  To connect a device to the extender Ethernet portInstall the Extender as an Access Point  To install the extender as an access pointSettings  To log in to the extender after the initial setup Log In After Initial SetupChange the admin Password  To change the password for the extenderSelect Maintenance Set Password Set Up Password Recovery for admin To set up password recovery Use Smart Setup to Connect the Extender to a Network Select Smart SetupManage the Extender Network and Settings Manage the Extender Network and Settings Add a WPS Client to the Extender Network Change the Basic WiFi Settings To view or change wireless setup  To add a WPS clientChange WiFi Security Settings Select Setup Wireless Setup To change the WiFi security setting  To view or change the advanced wireless settings View or Change Advanced Wireless SettingsSelect Advanced Wireless Settings View or Change the WPS Settings Set Up a Wireless Access List  To set up and enable the access listSelect the Turn Access Control On check box View or Change the Internet IP Address Setting To view or change the Internet Sstup Select Setup Internet Setup Enable NAT in the Extender To enable NAT Manage Profiles  To edit a profileOperating Mode  To delete a profileSelect Advanced Operating Mode  To view or change the operating modeInternet Surfing Monitor and Maintain the Extender  To recover your password to access the extender Recover the admin PasswordBack Up the Extender Configuration  To back up the extender configuration settingsSelect Maintenance Backup Settings Restore Saved Configuration Settings To restore the extender configuration settings Use the Factory Reset Button to Restore Factory Settings Return the Extender to Its Factory Settings To restore factory settings Erase the Settings and Return to Factory Settings Update the Firmware To erase the extender’s current settings Select Maintenance Firmware Update View Wired and Wireless Network Devices To view devices on the network Select Maintenance Attached Devices FAQs and Troubleshooting FAQs User name. adminCannot Log In to the Extender  To get the translated MAC addressCannot Join an Extender WiFi Network Connection was not established to the selected networkSupplemental Information Factory Default Settings Technical SpecificationsAC750 WiFi Range Extender Technical specifications

Related manuals

Manual 20 pages 1.69 Kb