NETGEAR EX6100100NAS user manual Factory Default Settings, Technical Specifications

Page 46

AC750 WiFi Range Extender

Factory Default Settings

The following table includes the factory settings for the extender. You can use the Factory Reset button or the Erase feature to return the extender to these settings. (See Return the Extender to Its Factory Settings on page 37.)

Table 2. Factory default settings

Feature	Setting

Setup Wizard	Enabled

Wireless communication	Enabled

Wireless network names (SSID)s	• 2.4 GHz network: EX6100_NETGEAR_2GEXT
	• 5 GHz network: EX6100_NETGEAR_5GEXT

Security	Disabled

Transmission speed	Auto1
Country/region	Varies by region

Operating mode	802.11ac, 802.11n, 802.11g, 802.11b, 802.11a

Data rate	Up to 300 Mbps for 2.4 GHz network and 433 Mbps for 5 GHz network

DHCP	Client enabled

1.Maximum wireless signal rate (IEEE Standard 802.11). Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.

Technical Specifications

The following table includes the product specifications.

Table 3. Technical specifications

Feature	Default behavior

Network protocol and standards	Data and routing protocols: TCP/IP, DHCP server and client, DNS
compatibility	relay, NAT (many-to-one)

Power consumption	100–240V~ 50/60 Hz, 0.21A maximum

Physical specifications	• Dimensions: 122 x 74 x 38 mm
	• Weight: 0.213 kg

Supplemental Information

46

Image 46

Contents AC750 WiFi Range Extender Compliance SupportTrademarks Contents FAQs and Troubleshooting Get to Know Your Extender Front Panel and Side Panel LEDs and Buttons WPS LEDUse as a WiFi Range Extender When to Use Your ExtenderHow the Extender Works Use as an Access Point Support for the 802.11ac Networking StandardInstall Your Extender Place the Extender Install the Extender as a Range ExtenderConnect to an Existing WiFi Network  To place the extenderExisting WiFi network name. MyNetworkName  To connect with the browser-based Smart SetupInstall Your Extender Install Your Extender Extender Performance Find the Best LocationConnect a Computer or Device to the Ethernet Port  To connect a computer to the extender Ethernet port  To connect a device to the extender Ethernet portInstall the Extender as an Access Point  To install the extender as an access pointSettings  To log in to the extender after the initial setup Log In After Initial SetupChange the admin Password  To change the password for the extenderSelect Maintenance Set Password Set Up Password Recovery for admin To set up password recovery Use Smart Setup to Connect the Extender to a Network Select Smart SetupManage the Extender Network and Settings Manage the Extender Network and Settings Add a WPS Client to the Extender Network Change the Basic WiFi Settings To view or change wireless setup  To add a WPS clientChange WiFi Security Settings Select Setup Wireless Setup To change the WiFi security setting  To view or change the advanced wireless settings View or Change Advanced Wireless SettingsSelect Advanced Wireless Settings View or Change the WPS Settings Set Up a Wireless Access List  To set up and enable the access listSelect the Turn Access Control On check box View or Change the Internet IP Address Setting To view or change the Internet Sstup Select Setup Internet Setup Enable NAT in the Extender To enable NAT Manage Profiles  To edit a profileOperating Mode  To delete a profileSelect Advanced Operating Mode  To view or change the operating modeInternet Surfing Monitor and Maintain the Extender  To recover your password to access the extender Recover the admin PasswordBack Up the Extender Configuration  To back up the extender configuration settingsSelect Maintenance Backup Settings Restore Saved Configuration Settings To restore the extender configuration settings Use the Factory Reset Button to Restore Factory Settings Return the Extender to Its Factory Settings To restore factory settings Erase the Settings and Return to Factory Settings Update the Firmware To erase the extender’s current settings Select Maintenance Firmware Update View Wired and Wireless Network Devices To view devices on the network Select Maintenance Attached Devices FAQs and Troubleshooting FAQs User name. adminCannot Log In to the Extender  To get the translated MAC addressCannot Join an Extender WiFi Network Connection was not established to the selected networkSupplemental Information Factory Default Settings Technical SpecificationsAC750 WiFi Range Extender Technical specifications

Related manuals

Manual 20 pages 1.69 Kb