3Com manual Utilities for the Solaris 2.5 platforms, Ruuhp111.1, Ruuaix111.1

Page 29

30NETBUILDER SOFTWARE VERSION 11.1 RELEASE NOTES

Item Not Supported The NETBuilder software version 11.1 does not support the following bridge/routers:

SuperStack II NETBuilder 227 Full Router (Ethernet)

SuperStack II NETBuilder 427 Router (Ethernet, ISDN)

NETBuilder Upgrade This section includes information about NETBuilder software version 11.1 Management Utilities NETBuilder Upgrade Management Utilities. Upgrade Link is a graphical

interface-based application designed to simplify upgrading the NETBuilder bridge/router operating software.

The NETBuilder software version 11.1 NETBuilder Upgrade Management Utilities support upgrades from NETBuilder bridge/routers running version 8.x through

11.0.1.If you need to upgrade from version 7.x to 11.1, you need to perform the upgrade in two steps. The first step requires upgrading from 7.x to 9.3.1. After the NETBuilder bridge/router configuration files have been converted to 9.3.1, they can then be further upgraded to support the 11.1 release. The 9.3.1 Remote Upgrade Utilities and manual are available on the 3Com InfoDeli website.

Downloading The NETBuilder Upgrade Management Utilities is shipped on the CD-ROM with NETBuilder Upgrade every NETBuilder software release. In addition, the NETBuilder Upgrade

Management Utilities Management Utilities can be downloaded from the FTP site (ftp.3com.com), from the World Wide Web access through http://infodeli.3com.com/, or from the 3Com bulletin board service (BBS) under Software Downloads, System Software. The files range in size from 1 MB to 4 MB per file and are usually easier and faster to retrieve using the FTP site.

UNIX Files The NETBuilder Upgrade Management Utilities are UNIX files compressed with the UNIX compress utility. To use the downloaded files, you must first expand the files using the UNIX decompress utility. For instructions on how to download and decompress the utilities, see the ruu111.txt file.

The UNIX files are as follows:

ruusol111.1

Contains the UNIX-compressed NETBuilder Upgrade Management

 

Utilities for the Solaris 2.5 platforms.

ruuhp111.1

Contains the UNIX-compressed NETBuilder Upgrade Management

 

Utilities for the HP-UX 10.x platforms.

ruuaix111.1

Contains the UNIX-compressed NETBuilder Upgrade Management

 

Utilities for the IBM AIX 4.1.1 through 4.2.X platforms.

ruu111.txt

Contains the instructions for downloading and decompressing

 

the NETBuilder Upgrade Management Utilities. This file also

 

contains instructions on how to integrate the utilities into the

 

Transcend Enterprise Manger application.

Windows Files The NETBuilder Upgrade Management Utilities are Windows files compressed with a compression utility. To use the downloaded files, you must first expand them using the decompress utility PKUNZip. PKUNZip can be downloaded from the following URLs:

http://www.pkware.com

Image 29
Contents NETBuilder Family Software Version 11.1 Release Notes Bayfront Plaza 3Com CorporationSanta Clara, California 95052-8145Contents CPU Utilization Statistic Deleting ATM Neighbors Web Link Documentation Path Zmodem Time Out Known ProblemsBcmfdinteg File Conversion Considerations NAT Proxy ARP RouteDiscovery Sdhlc Half-Duplex Mode Web Link Login SupportDisplaying Configuration Profiles Dynamic Paths Limitations Accm Not ConfigurableCONFiguration Authentication Header AHConfiguring IPsec How IPsec Works PoliciesStatPollInterval Encryption Netbuilder Software Version Release NotesPackages Contact 3Com or your network supplierSupported PC Flash Memory Cards New ProductsLists 3Comapproved vendors of the PC flash memory card Approved 20 MB Flash Memory CardsVPN Features Layer Two Tunneling Protocol New FeaturesApproved Dram SIMMsAdditional RAS Enhancements Extensible Authentication ProtocolDhcp Proxy Encryption StrengthSummary of Encryption Strengths Virtual Circuit PrioritizationEncryption Key Algorithm Package ID LengthBGP-4 Enhancements IP Version 6 PhaseFirewall Enhancements Frame Relay PVC Q.933 Support Ospf Not-So-Stubby-Area NssaData Over Voice B-Channel Isdn Specification Boundary Router Remote LAN DetectionToken Ring in Fast Ethernet Tife Features Ascii Boot56/64K CSU/DSU External Loopback NETBuilder Web Link ImprovementsApplication Notes Upgrade Management Utilities and NETBuilder Upgrade LinkFlash Load Placing a Data OverToggle the respective paths. Type ExampleNew Features Application Notes Version 11.1 for the NETBuilder bridge/router platforms NETBuilder II Software FeaturesSoftware NETBuilder II Firmware Requirements Other FeaturesNETBuilder II Firmware Requirements IBM ProtocolsSuperStack II NETBuilder SI Software Features 458 438Memory Requirements SuperStack II NETBuilder Ethernet and Token Ring FeaturesModels Features Token Ring Models Features Token Ring WAN Protocols OfficeConnect NETBuilder Software FeaturesModel and Software Package 112 132 111 145 131112 131 120 132 Additional OfficeConnect NETBuilder Models Software Features 136 117 137116 Memory Requirements Ruuhp111.1 Utilities for the Solaris 2.5 platformsUtilities for the HP-UX 10.x platforms Ruuaix111.1NETBuilder Upgrade Management Utilities Etc/passwd. You must add an entry can be ignored Known IssuesBridge Static Routes PROfile ServiceDLSw SVCsToken Ring a non-source routed frame Dialog boxes will be fully visible without scrollingSupported Asynchronous Modems Ports in DCE ModeSupported Synchronous Modem ModemsHistory, the PPP link does not come up IBM-Related Feature Settings for Token Ring Ports 3Com Bridge/Routers and Supported Features Token Ring Frame Copy ErrorsFrame Copy Errors under LAN Net Manager Known Problems Value Interrupt the boot cycle and enter monitor modeThis system SHow !profileID -PROFILE CONFiguration Notation Known Problems ADD !v1 -PPP ARU user, password Limitations Number of TCP Connections Processor/Frame Relay Relay port is Access for LLC2 TrafficFront-End IBM Boundary RoutingMultilink PPP SpeedPort running PPP Snmp ManagementSdlc Adjacent Link Service Point Source-RouteStations for Appn Source RouteSoftware Update Pages Using Netbuilder FamilyProcedures in this section describe how to configure IPsec Configuring IpsecConfiguring IPsec Replace with this chapterOn bridge/router, 2 enter Creating an Encryption PolicyCreating a Security Policy On bridge/router 2, enterManual key information, use For example, to create a new encryption key set, enterConfidentiality and data integrity To disable Ipsec on port 1, enterAssign an IP address to the tunnel virtual port by entering Enable Layer 2 Tunnelling by enteringCreate a route between the two tunnel endpoints by entering Configure an Ipsec policy/security association by enteringHow IPsec Works Enable Layer 2 Tunnelling Pptp by enteringCreate a route between two tunnel endpoints by entering Intercepted and viewedHow IPsec Works Configuring Ipsec Reference for Netbuilder Family CONFiguration Ipsec Service ParametersIpsec Service Parameters and Commands CONTrolKeySet ManualPOLicy ManualKeyInfoPolicyname Name you assign to the policy you are adding Is assigned dynamically using Ipcp or DhcpBe all or ALL Srcipaddr/maskPhase of the encrypt-decrypt-encrypt Encrypt phases, and the second 8 bytes for the decryptSpecifies Cipher Block Chaining mode of the Data 239.255.255.254Ipsec Service Parameters Rsvp Service Parameters REQuest MaxFlowRateRESerVation UDPEndcapPlace this page in front of Chapter SR Service ParametersAllRoutes ROUte ROUte SR Service Parameters SYS Service Parameters SYS Service Parameters StatPollInterval Weblink Service ParametersWeblink Service Parameters