3Com 11.1 Configuring IPsec, How IPsec Works Policies, Authentication Header AH, AllRoutes ROUte

Page 6

SDLC Ports and NetView Service Point

48

Source-Route Transparent Gateway

48

Token Ring+ Modules

48

 

 

VRRP Configuration

48

 

 

 

 

 

 

CONFIGURING IPSEC

 

 

 

Configuring IPsec

51

 

 

 

Creating Policies

51

 

 

 

Creating Key Sets 52

 

 

Configuring Manual Key Information

53

Enabling IPsec

54

 

 

 

Setting up a

 

 

 

 

VPN PPTP Tunnel

54

 

 

 

Establishing the Dialup Tunnel

56

 

How IPsec Works

56

 

 

 

Policies 57

 

 

 

 

Encapsulation Security Payload (ESP)

57

Authentication Header (AH)

58

 

IPSEC SERVICE PARAMETERS

CONFiguration 61 CONTrol 61 KeyEncryptionKey 61 KeySet 62 ManualKeyInfo 63 manualPOLicy 63

RSVP SERVICE PARAMETERS

CONFiguration 67

CONTrol 67

MaxFlowRate 68

REQuest 68

RESerVation 68

UDPEndcap 68

SR SERVICE PARAMETERS

AllRoutes 69

ROUte 70

SYS SERVICE PARAMETERS

CONFiguration 73

Page 5 Page 7
Image 6
Page 5 Page 7
Contents NETBuilder Family Software Version 11.1 Release Notes Santa Clara, California 3Com CorporationBayfront Plaza 95052-8145Contents Web Link Documentation Path Zmodem Time Out Known Problems Bcmfdinteg File Conversion ConsiderationsCPU Utilization Statistic Deleting ATM Neighbors Displaying Configuration Profiles Dynamic Paths Web Link Login SupportNAT Proxy ARP RouteDiscovery Sdhlc Half-Duplex Mode Limitations Accm Not ConfigurableConfiguring IPsec Authentication Header AHCONFiguration How IPsec Works PoliciesStatPollInterval Packages Netbuilder Software Version Release NotesEncryption Contact 3Com or your network supplierLists 3Comapproved vendors of the PC flash memory card New ProductsSupported PC Flash Memory Cards Approved 20 MB Flash Memory CardsApproved Dram New FeaturesVPN Features Layer Two Tunneling Protocol SIMMsDhcp Proxy Extensible Authentication ProtocolAdditional RAS Enhancements Encryption StrengthEncryption Key Virtual Circuit PrioritizationSummary of Encryption Strengths Algorithm Package ID LengthIP Version 6 Phase Firewall EnhancementsBGP-4 Enhancements Data Over Voice B-Channel Isdn Specification Ospf Not-So-Stubby-Area NssaFrame Relay PVC Q.933 Support Boundary Router Remote LAN Detection56/64K CSU/DSU External Loopback Features Ascii BootToken Ring in Fast Ethernet Tife NETBuilder Web Link ImprovementsFlash Load Upgrade Management Utilities and NETBuilder Upgrade LinkApplication Notes Placing a Data OverExample Toggle the respective paths. TypeNew Features Application Notes NETBuilder II Software Features SoftwareVersion 11.1 for the NETBuilder bridge/router platforms NETBuilder II Firmware Requirements Other FeaturesNETBuilder II Firmware Requirements IBM ProtocolsSuperStack II NETBuilder SI Software Features 438 458SuperStack II NETBuilder Ethernet and Token Ring Features Models Features Token RingMemory Requirements Model and Software Package 112 132 111 145 OfficeConnect NETBuilder Software FeaturesModels Features Token Ring WAN Protocols 131112 131 120 132 Additional OfficeConnect NETBuilder Models Software Features 117 137 116136 Memory Requirements Utilities for the HP-UX 10.x platforms Utilities for the Solaris 2.5 platformsRuuhp111.1 Ruuaix111.1NETBuilder Upgrade Management Utilities Known Issues Etc/passwd. You must add an entry can be ignoredDLSw PROfile ServiceBridge Static Routes SVCsDialog boxes will be fully visible without scrolling Token Ring a non-source routed frameSupported Synchronous Modem Ports in DCE ModeSupported Asynchronous Modems ModemsHistory, the PPP link does not come up IBM-Related Feature Settings for Token Ring Ports Token Ring Frame Copy Errors Frame Copy Errors under LAN Net Manager3Com Bridge/Routers and Supported Features Known Problems Interrupt the boot cycle and enter monitor mode This systemValue SHow !profileID -PROFILE CONFiguration Notation Known Problems ADD !v1 -PPP ARU user, password Limitations Front-End Processor/Frame Relay Relay port is Access for LLC2 TrafficNumber of TCP Connections IBM Boundary RoutingPort running PPP SpeedMultilink PPP Snmp ManagementStations for Appn Service Point Source-RouteSdlc Adjacent Link Source RouteUsing Netbuilder Family Software Update PagesConfiguring IPsec Configuring IpsecProcedures in this section describe how to configure IPsec Replace with this chapterCreating a Security Policy Creating an Encryption PolicyOn bridge/router, 2 enter On bridge/router 2, enterFor example, to create a new encryption key set, enter Manual key information, useTo disable Ipsec on port 1, enter Confidentiality and data integrityCreate a route between the two tunnel endpoints by entering Enable Layer 2 Tunnelling by enteringAssign an IP address to the tunnel virtual port by entering Configure an Ipsec policy/security association by enteringCreate a route between two tunnel endpoints by entering Enable Layer 2 Tunnelling Pptp by enteringHow IPsec Works Intercepted and viewedHow IPsec Works Configuring Ipsec Reference for Netbuilder Family Ipsec Service Parameters and Commands Ipsec Service ParametersCONFiguration CONTrolKeySet ManualKeyInfo ManualPOLicyBe all or ALL Is assigned dynamically using Ipcp or DhcpPolicyname Name you assign to the policy you are adding Srcipaddr/maskSpecifies Cipher Block Chaining mode of the Data Encrypt phases, and the second 8 bytes for the decryptPhase of the encrypt-decrypt-encrypt 239.255.255.254Ipsec Service Parameters Rsvp Service Parameters RESerVation MaxFlowRateREQuest UDPEndcapSR Service Parameters AllRoutesPlace this page in front of Chapter ROUte ROUte SR Service Parameters SYS Service Parameters SYS Service Parameters Weblink Service Parameters StatPollIntervalWeblink Service Parameters
Top Page Image Contents