3Com 11.1 manual Bridge Static Routes, DLSw, PROfile Service, SVCs

Page 32

Upgrade Management Known Issues 33

WARNING: Do not use the bcmfdinteg utility. The bcmfdinteg utility is used internally by the bcminstall utility. The bcmfdinteg utility should not be used by itself, because by default it removes all files from the current directory.

File Conversion This section describes file conversion considerations for APPN, bridge static routes, Considerations DLSw, the PROfile service, and X.25 SVCs.

APPN

APPN file conversion is supported in software version 8.2 and later. Upgrading from software versions prior to 8.2 requires manual configuration.

High Performance Routing (HPR) is a new feature for the NETBuilder bridge/router after software version 8.3. If you use the Upgrade Management Utilities to convert your APPN data file from version 8.3 (or later) to 11.1, be sure to turn on HPR if HPR is desired using:

SETDefault !<port> -APPN PortDef = <DLC type> HPR=yes

Bridge Static Routes

A static bridge route configured with the off option does not convert properly. You must manually reconfigure this route.

DLSw

Initial Bandwidth for Peer is a new parameter for software version 8.3 and later. The default for version 11.0 is 8000. If you use the Upgrade Management Utilities to convert your DLSw data files from version 8.3 (or later) to 11.1, be sure to set the value of the parameter to the desired value using:

SETDefault <tunnel id> -Dlsw PEER = <IP address> <PrioMode> <8000 other

value>

PROfile Service

Software version 8.0 and later includes the PROfile Service. Many parameters that belong to the X25 Service were moved to this service. Because the mapping is not one-to-one, the upgrade utility does not convert all parameters. After upgrading from pre-8.0 version software, delete the X25 Service configuration file and reconfigure the parameters under the X25 Service.

The X25VCLIMIT, X25VCTimer, and X25QueueSize parameters, previously in the network layer protocols services (AppleTalk, DECnet, IP, IPX, and so on), were moved to the PROfile Service. If you configured any of these parameters, you need to reconfigure them.

X.25 SVCs

The default values of the X25 Service parameters have changed from versions of software prior to 8.0. To ensure that call initiation between mixed versions of X.25 software is successful, you must configure the Twoway SVCs parameter on both ends of the X.25 connection to the same value.

Upgrading From Release If you are upgrading a NETBuilder from release 8.3 or earlier, you must disable user

8.3or Earlier verification by specifying the -NA flag on bcmnbrus or Upgrade Link. For example:

bcmnbrus -NA

Page 31 Page 33
Image 32
Page 31 Page 33
Contents NETBuilder Family Software Version 11.1 Release Notes 3Com Corporation Bayfront PlazaSanta Clara, California 95052-8145Contents CPU Utilization Statistic Deleting ATM Neighbors Web Link Documentation Path Zmodem Time Out Known ProblemsBcmfdinteg File Conversion Considerations Web Link Login Support NAT Proxy ARP RouteDiscovery Sdhlc Half-Duplex ModeDisplaying Configuration Profiles Dynamic Paths Limitations Accm Not ConfigurableAuthentication Header AH CONFigurationConfiguring IPsec How IPsec Works PoliciesStatPollInterval Netbuilder Software Version Release Notes EncryptionPackages Contact 3Com or your network supplierNew Products Supported PC Flash Memory CardsLists 3Comapproved vendors of the PC flash memory card Approved 20 MB Flash Memory CardsNew Features VPN Features Layer Two Tunneling ProtocolApproved Dram SIMMsExtensible Authentication Protocol Additional RAS EnhancementsDhcp Proxy Encryption StrengthVirtual Circuit Prioritization Summary of Encryption StrengthsEncryption Key Algorithm Package ID LengthBGP-4 Enhancements IP Version 6 PhaseFirewall Enhancements Ospf Not-So-Stubby-Area Nssa Frame Relay PVC Q.933 SupportData Over Voice B-Channel Isdn Specification Boundary Router Remote LAN DetectionFeatures Ascii Boot Token Ring in Fast Ethernet Tife56/64K CSU/DSU External Loopback NETBuilder Web Link ImprovementsUpgrade Management Utilities and NETBuilder Upgrade Link Application NotesFlash Load Placing a Data OverExample Toggle the respective paths. TypeNew Features Application Notes Version 11.1 for the NETBuilder bridge/router platforms NETBuilder II Software FeaturesSoftware Other Features NETBuilder II Firmware RequirementsNETBuilder II Firmware Requirements IBM ProtocolsSuperStack II NETBuilder SI Software Features 438 458Memory Requirements SuperStack II NETBuilder Ethernet and Token Ring FeaturesModels Features Token Ring OfficeConnect NETBuilder Software Features Models Features Token Ring WAN ProtocolsModel and Software Package 112 132 111 145 131112 131 120 132 Additional OfficeConnect NETBuilder Models Software Features 136 117 137116 Memory Requirements Utilities for the Solaris 2.5 platforms Ruuhp111.1Utilities for the HP-UX 10.x platforms Ruuaix111.1NETBuilder Upgrade Management Utilities Known Issues Etc/passwd. You must add an entry can be ignoredPROfile Service Bridge Static RoutesDLSw SVCsDialog boxes will be fully visible without scrolling Token Ring a non-source routed framePorts in DCE Mode Supported Asynchronous ModemsSupported Synchronous Modem ModemsHistory, the PPP link does not come up IBM-Related Feature Settings for Token Ring Ports 3Com Bridge/Routers and Supported Features Token Ring Frame Copy ErrorsFrame Copy Errors under LAN Net Manager Known Problems Value Interrupt the boot cycle and enter monitor modeThis system SHow !profileID -PROFILE CONFiguration Notation Known Problems ADD !v1 -PPP ARU user, password Limitations Processor/Frame Relay Relay port is Access for LLC2 Traffic Number of TCP ConnectionsFront-End IBM Boundary RoutingSpeed Multilink PPPPort running PPP Snmp ManagementService Point Source-Route Sdlc Adjacent LinkStations for Appn Source RouteUsing Netbuilder Family Software Update PagesConfiguring Ipsec Procedures in this section describe how to configure IPsecConfiguring IPsec Replace with this chapterCreating an Encryption Policy On bridge/router, 2 enterCreating a Security Policy On bridge/router 2, enterFor example, to create a new encryption key set, enter Manual key information, useTo disable Ipsec on port 1, enter Confidentiality and data integrityEnable Layer 2 Tunnelling by entering Assign an IP address to the tunnel virtual port by enteringCreate a route between the two tunnel endpoints by entering Configure an Ipsec policy/security association by enteringEnable Layer 2 Tunnelling Pptp by entering How IPsec WorksCreate a route between two tunnel endpoints by entering Intercepted and viewedHow IPsec Works Configuring Ipsec Reference for Netbuilder Family Ipsec Service Parameters CONFigurationIpsec Service Parameters and Commands CONTrolKeySet ManualKeyInfo ManualPOLicyIs assigned dynamically using Ipcp or Dhcp Policyname Name you assign to the policy you are addingBe all or ALL Srcipaddr/maskEncrypt phases, and the second 8 bytes for the decrypt Phase of the encrypt-decrypt-encryptSpecifies Cipher Block Chaining mode of the Data 239.255.255.254Ipsec Service Parameters Rsvp Service Parameters MaxFlowRate REQuestRESerVation UDPEndcapPlace this page in front of Chapter SR Service ParametersAllRoutes ROUte ROUte SR Service Parameters SYS Service Parameters SYS Service Parameters Weblink Service Parameters StatPollIntervalWeblink Service Parameters
Top Page Image Contents