3Com 11.1 manual MaxFlowRate, REQuest, RESerVation, UDPEndcap

Page 65

68CHAPTER 60: RSVP SERVICE PARAMETERS

MaxFlowRate

Syntax SETD !<port> -RSVP MaxFlowRate = <bytes/sec>(0-562500)

SHow [ !<port> !* ] -RSVP MaxFlowRate

Default Amount of bandwidth reserved for RSVP.

Description The MaxFlowRate parameter specifies the maximum amount of bandwidth in bytes/sec that can be allocated to a single flow.

REQuest

Syntax SHow [ !<port> !* ] -RSVP REQuest

Default No default

Description The REQuest parameter displays the outstanding RSVP reservation requests, that is a PATH was message sent but a corresponding RESV message has not been received, or a reservation request was denied at the local interface.

RESerVation

Syntax SHow [ !<port> !* ] RESerVation

Default No Default

Description The RESerVation parameter displays the current active reservations.

UDPEndcap

Syntax SETD !<port> UDPEncap = ([Enable Disable])< IP Multicast Address >

Default

SHow [ !<port> !* ] UDPMultiCast

Default Disabled. Only IP-encapsulated RSVP UDPEncap messages are sent unless UDP-only host presence is learned via the receipt of UDP-encapsulated RSVP messages.

Description The UDPEndcap parameter controls the UDP encapsulated RSVP messages. Normally, the NETBuilder bridge/router learns of a UDP host or hosts present at an interface by listening for UDP-encapsulated Path messages that were sent to either the well-known multicast address, 224.0.0.14, or to the address of the interface itself. However, if no UDP-encapsulated path message is received at the interface, the UDPEndcap parameter must be explicitly configured on the interface for the NETBuilder bridge/router to send UDP-encapsulated RSVP messages to a UDP host that is connected at the interface.

If the UDPEndcap parameter is enabled, RSVP messages are sent

UDP-encapsulated as well as in raw IP mode at the specified interface. If the

UDPEndcap parameter is disabled, RSVP messages are sent in raw IP format only.

Image 65
Contents NETBuilder Family Software Version 11.1 Release Notes Bayfront Plaza 3Com CorporationSanta Clara, California 95052-8145Contents CPU Utilization Statistic Deleting ATM Neighbors Web Link Documentation Path Zmodem Time Out Known ProblemsBcmfdinteg File Conversion Considerations NAT Proxy ARP RouteDiscovery Sdhlc Half-Duplex Mode Web Link Login SupportDisplaying Configuration Profiles Dynamic Paths Limitations Accm Not ConfigurableCONFiguration Authentication Header AHConfiguring IPsec How IPsec Works PoliciesStatPollInterval Encryption Netbuilder Software Version Release NotesPackages Contact 3Com or your network supplierSupported PC Flash Memory Cards New ProductsLists 3Comapproved vendors of the PC flash memory card Approved 20 MB Flash Memory CardsVPN Features Layer Two Tunneling Protocol New FeaturesApproved Dram SIMMsAdditional RAS Enhancements Extensible Authentication ProtocolDhcp Proxy Encryption StrengthSummary of Encryption Strengths Virtual Circuit PrioritizationEncryption Key Algorithm Package ID LengthBGP-4 Enhancements IP Version 6 PhaseFirewall Enhancements Frame Relay PVC Q.933 Support Ospf Not-So-Stubby-Area NssaData Over Voice B-Channel Isdn Specification Boundary Router Remote LAN DetectionToken Ring in Fast Ethernet Tife Features Ascii Boot56/64K CSU/DSU External Loopback NETBuilder Web Link ImprovementsApplication Notes Upgrade Management Utilities and NETBuilder Upgrade LinkFlash Load Placing a Data OverToggle the respective paths. Type ExampleNew Features Application Notes Version 11.1 for the NETBuilder bridge/router platforms NETBuilder II Software FeaturesSoftware NETBuilder II Firmware Requirements Other FeaturesNETBuilder II Firmware Requirements IBM ProtocolsSuperStack II NETBuilder SI Software Features 458 438Memory Requirements SuperStack II NETBuilder Ethernet and Token Ring FeaturesModels Features Token Ring Models Features Token Ring WAN Protocols OfficeConnect NETBuilder Software FeaturesModel and Software Package 112 132 111 145 131112 131 120 132 Additional OfficeConnect NETBuilder Models Software Features 136 117 137116 Memory Requirements Ruuhp111.1 Utilities for the Solaris 2.5 platformsUtilities for the HP-UX 10.x platforms Ruuaix111.1NETBuilder Upgrade Management Utilities Etc/passwd. You must add an entry can be ignored Known IssuesBridge Static Routes PROfile ServiceDLSw SVCsToken Ring a non-source routed frame Dialog boxes will be fully visible without scrollingSupported Asynchronous Modems Ports in DCE ModeSupported Synchronous Modem ModemsHistory, the PPP link does not come up IBM-Related Feature Settings for Token Ring Ports 3Com Bridge/Routers and Supported Features Token Ring Frame Copy ErrorsFrame Copy Errors under LAN Net Manager Known Problems Value Interrupt the boot cycle and enter monitor modeThis system SHow !profileID -PROFILE CONFiguration Notation Known Problems ADD !v1 -PPP ARU user, password Limitations Number of TCP Connections Processor/Frame Relay Relay port is Access for LLC2 TrafficFront-End IBM Boundary RoutingMultilink PPP SpeedPort running PPP Snmp ManagementSdlc Adjacent Link Service Point Source-RouteStations for Appn Source RouteSoftware Update Pages Using Netbuilder FamilyProcedures in this section describe how to configure IPsec Configuring IpsecConfiguring IPsec Replace with this chapterOn bridge/router, 2 enter Creating an Encryption PolicyCreating a Security Policy On bridge/router 2, enterManual key information, use For example, to create a new encryption key set, enterConfidentiality and data integrity To disable Ipsec on port 1, enterAssign an IP address to the tunnel virtual port by entering Enable Layer 2 Tunnelling by enteringCreate a route between the two tunnel endpoints by entering Configure an Ipsec policy/security association by enteringHow IPsec Works Enable Layer 2 Tunnelling Pptp by enteringCreate a route between two tunnel endpoints by entering Intercepted and viewedHow IPsec Works Configuring Ipsec Reference for Netbuilder Family CONFiguration Ipsec Service ParametersIpsec Service Parameters and Commands CONTrolKeySet ManualPOLicy ManualKeyInfoPolicyname Name you assign to the policy you are adding Is assigned dynamically using Ipcp or DhcpBe all or ALL Srcipaddr/maskPhase of the encrypt-decrypt-encrypt Encrypt phases, and the second 8 bytes for the decryptSpecifies Cipher Block Chaining mode of the Data 239.255.255.254Ipsec Service Parameters Rsvp Service Parameters REQuest MaxFlowRateRESerVation UDPEndcapPlace this page in front of Chapter SR Service ParametersAllRoutes ROUte ROUte SR Service Parameters SYS Service Parameters SYS Service Parameters StatPollInterval Weblink Service ParametersWeblink Service Parameters