3Com 11.1 manual Rsvp Service Parameters, Replace with this chapter

Page 64

60

RSVP SERVICE PARAMETERS

11.1Release Notes, Reference for NETBuilder Family Software

Replace Chapter 60 with this chapter.

This chapter describes the Resource Reservation Protocol (RSVP) Service parameters. RSVP is used in multicasting applications like video conferencing, multimedia, and virtual private network (VPN) network management. RSVP permits host applications to request Quality of Service from the network.

Table 2 RSVP Service Parameters and Commands

Parameters	Commands

CONFiguration	SHow
CONFiguration	SETDefault, SHow
MaxFlowRate	SETDefault, SHow
REQuest	SHow
RESerVation	SHow
UDPEndcap	SETDefault, SHow

CONFiguration

Syntax SHow -RSVP CONFiguration

Default None

Description The CONFiguration parameter displays all RSVP conﬁguration information for a PPP/Frame Relay port. The amount of bandwidth conﬁgured for RSVP via the PORT Service parameter, PROTocolRsrv, is displayed.

CONTrol

Syntax SETD -RSVP CONTrol = ENable DISable

SHow -RSVP CONTrol

Default DISable

Description The CONTrol parameter speciﬁes whether the RSVP capability is enabled. If RSVP is disabled, all RSVP messages are forwarded as IP data packets.

Image 64

Contents NETBuilder Family Software Version 11.1 Release Notes 3Com Corporation Bayfront PlazaSanta Clara, California 95052-8145Contents Bcmfdinteg File Conversion Considerations Web Link Documentation Path Zmodem Time Out Known ProblemsCPU Utilization Statistic Deleting ATM Neighbors Web Link Login Support NAT Proxy ARP RouteDiscovery Sdhlc Half-Duplex ModeDisplaying Conﬁguration Proﬁles Dynamic Paths Limitations Accm Not ConﬁgurableAuthentication Header AH CONFigurationConﬁguring IPsec How IPsec Works PoliciesStatPollInterval Netbuilder Software Version Release Notes EncryptionPackages Contact 3Com or your network supplierNew Products Supported PC Flash Memory CardsLists 3Comapproved vendors of the PC ﬂash memory card Approved 20 MB Flash Memory CardsNew Features VPN Features Layer Two Tunneling ProtocolApproved Dram SIMMsExtensible Authentication Protocol Additional RAS EnhancementsDhcp Proxy Encryption StrengthVirtual Circuit Prioritization Summary of Encryption StrengthsEncryption Key Algorithm Package ID LengthFirewall Enhancements IP Version 6 PhaseBGP-4 Enhancements Ospf Not-So-Stubby-Area Nssa Frame Relay PVC Q.933 SupportData Over Voice B-Channel Isdn Speciﬁcation Boundary Router Remote LAN DetectionFeatures Ascii Boot Token Ring in Fast Ethernet Tife56/64K CSU/DSU External Loopback NETBuilder Web Link ImprovementsUpgrade Management Utilities and NETBuilder Upgrade Link Application NotesFlash Load Placing a Data OverExample Toggle the respective paths. TypeNew Features Application Notes Software NETBuilder II Software FeaturesVersion 11.1 for the NETBuilder bridge/router platforms Other Features NETBuilder II Firmware RequirementsNETBuilder II Firmware Requirements IBM ProtocolsSuperStack II NETBuilder SI Software Features 438 458Models Features Token Ring SuperStack II NETBuilder Ethernet and Token Ring FeaturesMemory Requirements OfﬁceConnect NETBuilder Software Features Models Features Token Ring WAN ProtocolsModel and Software Package 112 132 111 145 131112 131 120 132 Additional OfﬁceConnect NETBuilder Models Software Features 116 117 137136 Memory Requirements Utilities for the Solaris 2.5 platforms Ruuhp111.1Utilities for the HP-UX 10.x platforms Ruuaix111.1NETBuilder Upgrade Management Utilities Known Issues Etc/passwd. You must add an entry can be ignoredPROﬁle Service Bridge Static RoutesDLSw SVCsDialog boxes will be fully visible without scrolling Token Ring a non-source routed framePorts in DCE Mode Supported Asynchronous ModemsSupported Synchronous Modem ModemsHistory, the PPP link does not come up IBM-Related Feature Settings for Token Ring Ports Frame Copy Errors under LAN Net Manager Token Ring Frame Copy Errors3Com Bridge/Routers and Supported Features Known Problems This system Interrupt the boot cycle and enter monitor modeValue SHow !profileID -PROFILE CONFiguration Notation Known Problems ADD !v1 -PPP ARU user, password Limitations Processor/Frame Relay Relay port is Access for LLC2 Trafﬁc Number of TCP ConnectionsFront-End IBM Boundary RoutingSpeed Multilink PPPPort running PPP Snmp ManagementService Point Source-Route Sdlc Adjacent LinkStations for Appn Source RouteUsing Netbuilder Family Software Update PagesConfiguring Ipsec Procedures in this section describe how to conﬁgure IPsecConﬁguring IPsec Replace with this chapterCreating an Encryption Policy On bridge/router, 2 enterCreating a Security Policy On bridge/router 2, enterFor example, to create a new encryption key set, enter Manual key information, useTo disable Ipsec on port 1, enter Conﬁdentiality and data integrityEnable Layer 2 Tunnelling by entering Assign an IP address to the tunnel virtual port by enteringCreate a route between the two tunnel endpoints by entering Conﬁgure an Ipsec policy/security association by enteringEnable Layer 2 Tunnelling Pptp by entering How IPsec WorksCreate a route between two tunnel endpoints by entering Intercepted and viewedHow IPsec Works Configuring Ipsec Reference for Netbuilder Family Ipsec Service Parameters CONFigurationIpsec Service Parameters and Commands CONTrolKeySet ManualKeyInfo ManualPOLicyIs assigned dynamically using Ipcp or Dhcp Policyname Name you assign to the policy you are addingBe all or ALL Srcipaddr/maskEncrypt phases, and the second 8 bytes for the decrypt Phase of the encrypt-decrypt-encryptSpecifies Cipher Block Chaining mode of the Data 239.255.255.254Ipsec Service Parameters Rsvp Service Parameters MaxFlowRate REQuestRESerVation UDPEndcapAllRoutes SR Service ParametersPlace this page in front of Chapter ROUte ROUte SR Service Parameters SYS Service Parameters SYS Service Parameters Weblink Service Parameters StatPollIntervalWeblink Service Parameters