Dynaudio SUB 600 owner manual ➐ SUB I/O, To Slave, ➑ LFE/Slave

Page 12

Controls and connections

 

 

 

 

POWER

GAIN

PHASE

ON AUTO

 

0° 180°

 

 

 

 

 

Min

Max

 

SAT Highpass

SUB Lowpass

Flat 60Hz 80Hz

 

 

50 Hz

150 Hz

 

 

SAT/SUB Input

SAT Output

 

LEFT

 

 

 

 

 

 

RIGHT

 

 

 

 

LFE / Slave IN

OUT

SUB I/O

 

To Slave

LFE

Slave

 

 

 

 

100-120V/220-240V

 

 

 

~ 50/60Hz 3.15A

ON

OFF

FUSE T3.15A L 250V

SUB I/O, To Slave

LFE/Slave IN: input for LFE signal from processor/receiver. Note that the signal must be a true LFE signal or already have been filtered by the processor/receiver, as SUB Lowpass does not have an effect in combination with the LFE input.

OUT: output to next subwoofer if installed.

LFE/Slave

Subwoofer operation mode LFE or Slave:

LFE: setting if just one subwoofer is used or for first subwoofer if system consists of multiple subwoofers. Note that the SUB Lowpass control does not have an effect when the LFE Mode is selected.

Slave: setting for second and all following subwoofers. Note that the SUB Lowpass, PHASE and GAIN controls do not have an effect when the Slave Mode is selected.

ON/OFF

Main power switch (to switch the subwoofer manually on and off). LED: shows operation mode:

red = subwoofer switched on and in mute mode

green = subwoofer is activated

AC IN

Main power input.

Owners Manual

9

Image 12
Contents Page Contents Page Introduction Important Safety Instructions Risk of Electric Shock. Do Not Open Vases, should not be placed on this apparatusSupply cord shall remain readily operable Qualified personnelUsed signs and symbols Safety signsGeneral safety sign Signal wordsHow this operating manual is structured Text markingsCheck that the contents are complete UnpackingTo unpack the subwoofer Grille To remove the grilleTo fit the grille Controls and connections ➍ SAT Highpass➎ SUB Lowpass ➏ SAT/SUB Input, SAT Output➐ SUB I/O, To Slave ➑ LFE/SlaveConnecting the subwoofer Damage of device due to improper connectionHighpass setting Subwoofer inputsSUB I/O LFE/Slave SAT/SUB InputConnecting a single subwoofer ➊ To connect the SAT/SUB inputSUB Input ➋ To connect the LFE channelMultiple subwoofer connections To connect multiple subwoofersConnecting loudspeakers To connect speakersSwitching the subwoofer on/off Power modeAuto Power mode Adjusting the volume Gain High Sound LevelsSelecting the subwoofer cut-off frequency SUB Lowpass To select the cut-off frequencySetting the phase Phase To find the correct phase settingSetting the satellite cut-off frequency SAT Highpass To set the cut-off frequencyPositioning the subwoofer Choose adequate music materialImpact of room-modes Listening RoomCorner placement Positioning possibilitiesNext to wall, away from corner Free standing, away from wall and cornerUsing multiple subwoofers General tips Volume Gain Cut-off frequenciesCross-over frequencies set correctly Subwoofer too low, main speakers too highSubwoofer too high, main speakers too low Control possibilities General tips SUB Lowpass = 80 Hz  Reduce weak amplifiers and small speakers from bass loadSpecific tips Damage of Small Satellite SpeakersSUB Lowpass = 150 Hz at the very right SAT Highpass = Flat Cut-off frequencies Troubleshooting Check this firstTroubleshooting Care and Maintenance Cleaning the cabinetTo clean the cabinet Damage of drive unitsChanging the fuse Recycling used productsRisk of Fire To change the fuseWarranty Technical specifications Parameter SubPage Page Page All there is

SUB 600 specifications

The Dynaudio SUB 600 is a powerful subwoofer designed to bring an enhanced level of bass performance to home audio systems. Known for its robust build quality and exceptional sound reproduction, the SUB 600 is a versatile choice for audiophiles and home theater enthusiasts alike.

One of the standout features of the Dynaudio SUB 600 is its impressive 18-inch driver, which is engineered to deliver deep, impactful bass across a wide frequency range. This driver utilizes advanced materials, including a specially designed cone and high-stiffness surround, to ensure minimal distortion and maximum clarity at high output levels. This means that whether you're enjoying music or watching an action-packed movie, you can expect a rich and immersive bass experience.

The SUB 600 is powered by a built-in amplifier that delivers a robust output of up to 500 watts RMS, capable of handling the most demanding audio tracks with ease. This amplifier is designed to work seamlessly with the subwoofer's driver, providing the necessary power and control to reproduce low frequencies accurately. The result is a dynamic sound that adds depth and presence to any audio setup.

Dynaudio has also integrated advanced technologies into the SUB 600 to optimize performance. The subwoofer features a sophisticated digital signal processing (DSP) system that allows for precise tuning of the low-frequency response. This ensures that the SUB 600 can adapt to different room acoustics, delivering the best possible bass performance regardless of placement.

Furthermore, the SUB 600 comes with a range of connectivity options, including high-level and low-level inputs. This allows it to easily integrate with various audio systems, from stereo setups to multi-channel home theaters. The inclusion of an adjustable crossover frequency control enables users to fine-tune the integration with their main speakers, ensuring a seamless blend of sound.

In terms of aesthetics, the Dynaudio SUB 600 boasts a sleek design that will fit well into any entertainment environment. It is available in a selection of finishes that can complement your existing decor. With its combination of high-quality materials, advanced technologies, and performance-driven design, the Dynaudio SUB 600 stands out as an exceptional choice for anyone seeking to elevate their audio experience to the next level. Whether for serious music listening or immersive movie watching, the SUB 600 delivers powerful bass that enhances any audio experience.