Dynaudio SUB 600 owner manual Multiple subwoofer connections, To connect multiple subwoofers

Page 16

Connecting the subwoofer

 

POWER

GAIN

PHASE

POWER

GAIN

PHASE

 

ON

AUTO

 

0° 180°

ON

AUTO

 

0° 180°

 

 

 

Min

Max

 

 

Min

Max

 

SAT Highpass

SUB Lowpass

SAT Highpass

SUB Lowpass

 

Flat 60Hz 80Hz

 

Flat 60Hz 80Hz

 

 

 

50 Hz

150 Hz

 

50 Hz

150 Hz

LFE/SUB

SAT/SUB Input

SAT Output

SAT/SUB Input

SAT Output

 

 

 

 

 

 

 

 

Out

LEFT

 

 

 

LEFT

 

 

 

 

RIGHT

 

 

 

RIGHT

 

 

 

Front Out/

LFE / Slave IN

OUT

LFE / Slave IN

OUT

 

 

 

 

 

 

 

 

Pre Out

SUB I/O

 

 

To Slave

SUB I/O

 

 

To Slave

 

LFE

Slave

 

LFE

Slave

 

 

 

 

Sub 1

 

 

Sub 2

 

 

 

(Master)

 

 

(Slave)

Sub...

(Slave)

Multiple subwoofer connections

The Dynaudio Sub 600 can be used stand-alone or together with multiple subwoofer units. Using multiple units may be helpful if the listening room is quite large or has difficult acoustic conditions (e.g. room-modes, see also “Positioning the subwoofer” on page 20 for further information).

When using two or more subwoofers, the first one (designated “Master”) controls the following subs (designated “Slave”) via a subwoofer cable.

To connect multiple subwoofers:

1.Connect the first subwoofer with the processor/receiver as described before.

2.Set MODE switch of first subwoofer to LFE.

3.From the OUT - To Slave output of the first subwoofer connect a mono RCA-to-RCA cable to the SUB I/O - LFE/Slave IN input of the following subwoofer. This now becomes the slave.

4.Set the MODE switch of the second subwoofer to Slave.

Further subwoofers can be connected in the same way. Set the MODE switch of all following subwoofers to Slave respectively.

Note: In order to avoid interference and noise, we recommend you use quality, well shielded cables.

When using multiple subwoofers in a Master-Slave setup, it is recommended that the subwoofers are all the same model.

If you wish to use multiple subwoofers with full individual control, set the Input switch for all to the “Master” position. From the Amplifier, processor or receiver’s subwoofer output, use a Y-connector.

Owners Manual

13

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Page Contents Page Introduction Important Safety Instructions Risk of Electric Shock. Do Not Open Vases, should not be placed on this apparatusSupply cord shall remain readily operable Qualified personnelUsed signs and symbols Safety signsGeneral safety sign Signal wordsHow this operating manual is structured Text markingsUnpacking Check that the contents are completeTo unpack the subwoofer To remove the grille GrilleTo fit the grille Controls and connections ➍ SAT Highpass➎ SUB Lowpass ➏ SAT/SUB Input, SAT Output➐ SUB I/O, To Slave ➑ LFE/SlaveConnecting the subwoofer Damage of device due to improper connectionHighpass setting Subwoofer inputsSUB I/O LFE/Slave SAT/SUB InputConnecting a single subwoofer ➊ To connect the SAT/SUB inputSUB Input ➋ To connect the LFE channelMultiple subwoofer connections To connect multiple subwoofersConnecting loudspeakers To connect speakersPower mode Switching the subwoofer on/offAuto Power mode Adjusting the volume Gain High Sound LevelsSelecting the subwoofer cut-off frequency SUB Lowpass To select the cut-off frequencySetting the phase Phase To find the correct phase settingSetting the satellite cut-off frequency SAT Highpass To set the cut-off frequencyPositioning the subwoofer Choose adequate music materialImpact of room-modes Listening RoomCorner placement Positioning possibilitiesNext to wall, away from corner Free standing, away from wall and cornerUsing multiple subwoofers General tips Volume Gain Cut-off frequenciesSubwoofer too low, main speakers too high Cross-over frequencies set correctlySubwoofer too high, main speakers too low Control possibilities General tips SUB Lowpass = 80 Hz  Reduce weak amplifiers and small speakers from bass loadDamage of Small Satellite Speakers Specific tipsSUB Lowpass = 150 Hz at the very right SAT Highpass = Flat Cut-off frequencies Troubleshooting Check this firstTroubleshooting Care and Maintenance Cleaning the cabinetTo clean the cabinet Damage of drive unitsChanging the fuse Recycling used productsRisk of Fire To change the fuseWarranty Technical specifications Parameter SubPage Page Page All there is

SUB 600 specifications

The Dynaudio SUB 600 is a powerful subwoofer designed to bring an enhanced level of bass performance to home audio systems. Known for its robust build quality and exceptional sound reproduction, the SUB 600 is a versatile choice for audiophiles and home theater enthusiasts alike.

One of the standout features of the Dynaudio SUB 600 is its impressive 18-inch driver, which is engineered to deliver deep, impactful bass across a wide frequency range. This driver utilizes advanced materials, including a specially designed cone and high-stiffness surround, to ensure minimal distortion and maximum clarity at high output levels. This means that whether you're enjoying music or watching an action-packed movie, you can expect a rich and immersive bass experience.

The SUB 600 is powered by a built-in amplifier that delivers a robust output of up to 500 watts RMS, capable of handling the most demanding audio tracks with ease. This amplifier is designed to work seamlessly with the subwoofer's driver, providing the necessary power and control to reproduce low frequencies accurately. The result is a dynamic sound that adds depth and presence to any audio setup.

Dynaudio has also integrated advanced technologies into the SUB 600 to optimize performance. The subwoofer features a sophisticated digital signal processing (DSP) system that allows for precise tuning of the low-frequency response. This ensures that the SUB 600 can adapt to different room acoustics, delivering the best possible bass performance regardless of placement.

Furthermore, the SUB 600 comes with a range of connectivity options, including high-level and low-level inputs. This allows it to easily integrate with various audio systems, from stereo setups to multi-channel home theaters. The inclusion of an adjustable crossover frequency control enables users to fine-tune the integration with their main speakers, ensuring a seamless blend of sound.

In terms of aesthetics, the Dynaudio SUB 600 boasts a sleek design that will fit well into any entertainment environment. It is available in a selection of finishes that can complement your existing decor. With its combination of high-quality materials, advanced technologies, and performance-driven design, the Dynaudio SUB 600 stands out as an exceptional choice for anyone seeking to elevate their audio experience to the next level. Whether for serious music listening or immersive movie watching, the SUB 600 delivers powerful bass that enhances any audio experience.
Top Page Image Contents