Source Technologies ST9530 STH Command, Password, Micr Definition Command SMCPxxxx$ optional

Page 23

NOTE: The &%STF command must be entered at the beginning of the print job before any other print data is received.

&%STH Command

The &%STH command does not set-up the printer for check printing activity as completely as the &%STF command mode. This alternate MICR mode command forces the user to manually program some commands through their host application. It is used when programmers cannot place &%STFPASSWORD$ at the beginning of their job. Use the &%STH command if you experience page ejects while in &%STF mode.

When entering MICR mode with the &%STH command, the printer will:

•Check to see if the proper Front Panel Combination has been entered (when enabled).

•Allow access to secure check printing resources such as MICR fonts and secure fonts which are stored in printer ROM. It also allows access to protected signatures, overlays, logos and other important resources stored in password protected nonvolatile flash memory.

•Turn Hex Transfer ON.

NOTE: The &%STH command can occur within a datastream after the page has started. The &%STH command, unlike the &%STF command, can be issued anywhere on the page.

MICR Mode Commands
Password Command	&%STFPASSWORD$ or &%STHPASSWORD$
&%STF or &%STH	Lead in sequence
PASSWORD	User defined password, 8 characters, case sensitive,
	unprintable characters allowed. Factory default is
	PASSWORD. See also New Password Command.
$	Command terminator
MICR Definition Command	&%SMCPxxxx$ (optional)
&%SMCP	Lead in sequence
xxxx	MICR count, the number of MICR lines to be printed during
	this print job. (4 bytes in hex)
$	Command terminator

Secure MICR Printer User’s Guide	19	© Source Technologies
September 2005	19	All Rights Reserved

Image 23

Contents ST9530 Secure Micr Printer User’s Guide Page Table of Contents Audit Trail Report Error MessagesPrinter Installation Micr Printing Today Micr OverviewCheck Processing System Secure Micr Printer User’s Guide Design Elements in Detail Paper General Features of Check DesignPosition and Dimension Gauge Micr Check DesignAmount Convenience Amount DuplexingMicr Clear Band Data Elements DateDrawee Institution Name Amount In WordsPayee Area Signature AreaExternal Processing Code EPC Field Position Memo LineCheck Serial Number Fractional Routing Number Micr Line Auxiliary On-Us Field Positions 65 toOn-Us Field Positions 32 to Sample Check Quality Issues Layout WeightMicr Check Stock QualityCheck Stock Security Features Security IssuesSecurity Note Secure Micr Printer User’s Guide Secure Fonts Micr FeaturesMicr Mode Micr Fonts @PJL Ustatus Device CODE=40020 MicroPrint Bi-Directional Feedback Micr Menu Resource StorageSTF Command Entering Micr ModeSmcp STH CommandPassword Micr Definition Command SMCPxxxx$ optionalPrint Micr E-13B Font SMDddd...ddd$ Set New Password Command &%STExxxxxxxx$STE STSPrint MicroPrint Line SMMxxxxxxxxx!$ Print Micr CMC7 Font SM7ddd...ddd$Print Secure Numeric Font SMFddd..ddd~ Print ICR Secure Numeric Font &%SMIxxxxxx~Format Flash Memory SFF$ Secure Flash Resource Unlock Command STPxxxxx$Tray Lock Command STTL#$ Load Flash Resource STLxxxxxyyyyyyzdd....ddSttson Tray Unlock Command STTU#$Tray Swapping Commands STTU#DES and AES Decryption Decryption CommandsTurn AES Decryption OFF Turn DES Decryption onTurn AES Decryption on Turn DES Decryption OFFCustomer Character Conversation Command STBEEP2$ Special Alert and Custom Beep CommandSTBEEP1$ MICRpoint Feature Secure Micr Printer User’s Guide Turning Hex Transfer Off IBM Host Programming Features and ExamplesHex Transfer Turning Hex Transfer OnHex Transfer Examples Micr Mode Command Example Micr font character mapping in Appendix a Commands in .1 in order of appearanceSTFPASSWORD$ Command terminatorExample &%STY2300$ Escape Character TranslationSTY4040$ STY4000$Sample Check Audit Trail Reports End Audit Record Audit Trail Report Command SetPrint Audit Report SARAudit Report Field Four SQ4d..d~ Audit Report Field One SQ1d..d$Audit Report Field Two-MICR Line Audit Report Field Three SQ3d..d$Print and Purge Audit Report &%SPURGExx$ Audit Report Field Five SQ5d..d$Audit Report Field Six SQ6d..d$ Audit Report Field Seven SQ7d..d$Print Audit Report SPRINTxx$ Start Audit Feedback CommandAudit Trail Commands Example Audit Trail Check Sample Terminator SAR$SQ1200$200 SQ6October 5, 2005$SQ7103345 AM$ SMD...$Msmith Action Error MessagesError Message on Display Printed Message DescriptionMacro Definition Error Invalid decode Page Example &%SMD 00001234 T01234567T3210987654321$ Will print Appendix a E13B Micr Font Mapping Command&%SMDddd..ddd$Appendix B CMC7 Micr Font Mapping Less Than Equal Greater Than Description Alpha/Numeric Hex Value Secure Font Character Appendix C Secure Numeric Font MappingTwo Three Four Five Six Seven Eight Nine Arrow Example&%SMF$15,575.00~ Appendix D ICR Secure Numeric Font Mapping Appendix E Micr Mode Command Summary STTSOFF$ Previous Audit Report information will be lost SPRINT$STORE$ SPURGE$Appendix G PJL Based Micr Commands PJL Re-Lock Sequence With a New Password Value @PJL Info Micr UELCartridge Status = Unknown PCL Font Calls, Positioning Commands and Variable Print Data Sample Accounts Payable Check PJL and PCL commands used to print the sample check ESC%-12345X@PJL Ldeletepassword LRESOURCEflash